Adam Tchorz

Mr. Adam Tchorz

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 July 2016 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
Marzanna KsiazekMarzanna Ksiazek
Marzanna Ksiazek
LBLukasz Boron
Lukasz Boron
MRMarta Radecka
Marta Radecka
Maria RichertMaria Richert
Maria Richert
ATAdam Tchorz
Adam Tchorz
The aim of the investigations was to compare the microstructure, mechanical, and wear properties of Cr3C2-NiCr+Ni and Cr3C2-NiCr coatings deposited by HVOF technique (the high-velocity oxygen fuel spray process) on ductile cast iron. The effect of nickel particles added to the chromium carbide coating on mechanical and wear behavior in the system of Cr 3 C 2 -NiCr+Ni/ductile cast iron was analyzed in order to improve the lifetime of coated materials. The structure with particular emphasis of characteristic of the interface in the system of composite coating (Cr 3 C 2 -NiCr+Ni)/ductile cast iron was studied using the optical, scanning, and transmission electron microscopes, as well as the analysis of chemical and phase composition in microareas. Experimental results show that HVOF-sprayed Cr3C2-NiCr+Ni composite coating exhibits low porosity, high hardness, dense structure with large, partially molten Ni particles and very fine Cr3C2 and Cr7C3 particles embedded in NiCr alloy matrix, coming to the size of nanocrystalline. The results were discussed in reference to examination of bending strength considering cracking and delamination in the system of composite coating (Cr 3 C 2 -NiCr+Ni)/ductile cast iron as well as hardness and wear resistance of the coating. The composite structure of the coating provides the relatively good plasticity of the coating, which in turn has a positive effect on the adhesion of coating to the substrate and cohesion of the composite coating (Cr3C2-NiCr+Ni) in wear conditions.

1 February 2016 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
EGElzbieta M. Godlewska
Elzbieta M. Godlewska
MKMars Krzysztof
Mars Krzysztof
PDPawel Drozdz
Pawel Drozdz
ATAdam Tchorz
Adam Tchorz
Marzanna KsiazekMarzanna Ksiazek
Marzanna Ksiazek

16 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
Marzanna KsiazekMarzanna Ksiazek
Marzanna Ksiazek
LBLukasz Boron
Lukasz Boron
ATAdam Tchorz
Adam Tchorz
Alumina oxide coatings are widely used in many industrial applications to improve corrosion protection, wear and erosion resistances, and thermal insulation of metallic surfaces. The paper presents study of the microstructure, mechanical, and wear properties of HVOF (high velocity oxy-fuel process) sprayed of Al2O3-15 wt.% TiO2 coating with the NiAl interlayer on the surface of Al-Si alloy castings. The microstructure of Al2O3-15 wt.% TiO2/NiAl coating was characterized by light microscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDS). The analysis of the microstructure showed the formation of coating with low porosity, compact structure, good adhesion to the substrate with typical lamellar structure composed of a solid phase consisting of compounds included in the coating material and their phase variations. For analysis of the adhesion of coatings to the substrate, the scratch test was applied. An assessment of the erosive wear resistance of coatings was also carried out, confirming the significant impact of the interlayer as well as the microstructure and phase composition of the oxide coating on the wear resistance of the tested coating system. Moreover, the results were discussed in relation to the bending strength test, including cracks and delamination in the system of the Al2O3-15 wt.% TiO2/NiAl/Al-Si alloy as microhardness and erosion resistance of the coating. It was found that the introduction of the NiAl metallic interlayer significantly increased resistance to cracking and wear behavior in the studied system.

1 September 2013 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
BMB. Mrzygłód
B. Mrzygłód
PMP. Matusiewicz
P. Matusiewicz
ATAdam Tchorz
Adam Tchorz
IOIzabela Olejarczyk-Wożeńska
Izabela Olejarczyk-Wożeńska
Stereological description of dispersed microstructure is not an easy task and remains the subject of continuous research. In its practical aspect, a correct stereological description of this type of structure is essential for the analysis of processes of coagulation and spheroidisation, or for studies of relationships between structure and properties. One of the most frequently used methods for an estimation of the density Nv and size distribution of particles is the Scheil - Schwartz - Saltykov method. In this article, the authors present selected methods for quantitative assessment of ductile iron microstructure, i.e. the Scheil - Schwartz - Saltykov method, which allows a quantitative description of three-dimensional sets of solids using measurements and counts performed on two-dimensional cross-sections of these sets (microsections) and quantitative description of three-dimensional sets of solids by X-ray computed microtomography, which is an interesting alternative for structural studies compared to traditional methods of microstructure imaging since, as a result, the analysis provides a three-dimensional imaging of microstructures examined.

21 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
ATAdam Tchorz
Adam Tchorz
KKKrzysztof Korona
Krzysztof Korona
IKIzabela Krzak
Izabela Krzak
ABAdam Bitka
Adam Bitka
Marzanna KsiazekMarzanna Ksiazek
Marzanna Ksiazek
DWDorota Wilk-Kołodziejczyk
Dorota Wilk-Kołodziejczyk
This paper presents an assessment of the possibility of using digital image classifiers for tomographic images concerning ductile iron castings. The results of this work can help the development of an efficient system suggestion allowing for decision making regarding the qualitative assessment of the casting process parameters. Special attention should be focused on the fact that automatic classification in the case of ductile iron castings is difficult to perform. The biggest problem in this aspect is the high similarity of the void image, which may be a sign of a defect, and the nodular graphite image. Depending on the parameters, the tests on different photos may look similar. Presented in this article are test scenarios of the module analyzing two-dimensional tomographic images focused on the comprehensive assessment by convolutional neural network models, which are designed to classify the provided image. For the purposes of the tests, three such models were created, different from each other in terms of architecture and the number of hyperparameters and trainable parameters. The described study is a part of the decision-making system, supporting the process of qualitative analysis of the obtained cast iron castings.

11 January 2016 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
Marzanna KsiazekMarzanna Ksiazek
Marzanna Ksiazek
LBLukasz Boron
Lukasz Boron
MRMarta Radecka
Marta Radecka
Maria RichertMaria Richert
Maria Richert
ATAdam Tchorz
Adam Tchorz