This study aimed to develop a safe and advanced antibacterial material of electrospun microfiber membranes (MFMs) for wound dressings. Combinations of several materials were investigated; thermal treatment and electrospinning techniques were used to form the best quality of MFMs to suit its end applications. By comparing the fiber morphology, diameter changes, and fracture strength, the suitable ratio of raw materials and thermal treatment were obtained before and after adding Trition X-100 as a surfactant for MFMs of sodium alginate/polyvinyl alcohol/polyethylene oxide (SA/PVA/PEO). The electrospinning solution was mixed with berberine as an antibacterial substance; meanwhile, calcium chloride (CaCl2) was used as the crosslinking agent. The antibacterial properties, water dissolution resistance, water content, and fracture strength were thoroughly investigated. The results showed that the antibacterial rates of MFMs with different mass fractions of berberine (0, 3, and 5 wt.%) to Escherichia coli (E. coli) were 14.7, 92.9, and 97.2%, respectively. The moisture content and fracture strength of MFMs containing 5 wt.% berberine were 72.0% and 7.8 MPa, respectively. In addition, the produced MFMs embodied great water dissolution resistance. Berberine-loaded SA/PVA/PEO MFMs could potentially serve as an antibacterial wound dressing substrate with low cost and small side effects.
Advanced research on improving the performance of conductive polymer composites is essential to exploring their potential in various applications. Thus, in this study, the electrical conductivity of multilayer nanofibre membranes composed of polyvinyl alcohol (PVA) with different electroconductive fillers content including zinc oxide (ZnO), multiwalled carbon nanotubes (MWNTs), and Ferro ferric oxide (Fe3O4), were produced via electrospinning. The tensile property and electrical conductivity of monolayer membranes were explored. The results showed that PVA with 2 wt.% MWNTs nanofibre membrane has the best conductivity (1.0 × 10−5 S/cm) and tensile strength (29.36 MPa) compared with other fillers. Meanwhile, the combination of multilayer membrane ZnO/Fe3O4/Fe3O4/MWNTs/ZnO showed the highest conductivity (1.39 × 10−5 S/cm). The parallel circuit and calculation of parallel resistance were attempted to demonstrate the conductive mechanism of multilayer membranes, which can predict the conductivity of other multilayer films. The production of multilayer composites that enhance electrical conductivity and improve conductive predictions was successfully explored.
24 April 2018 in Journal of Materials Science: Materials in Electronics
In order to find out the light color mixing mechanism of rare earth luminescent materials used in anti-counterfeiting fibers, we prepared three kinds of rare earth luminescent materials according to RGB tri-primary color, and mixed it together to form different mixtures in certain proportion. The phase structures of the luminescent material monomers were measured by X-ray diffractometer. The photochromic properties of the luminescent materials were tested and analyzed by fluorescence spectrophotometer. The results show that the light color mixing was consistent with the blending principle of additive color, but not the same because of the photochromic properties of rare earth luminescent materials, and we explored the reasons in the light wavelength and intensity. It was found that the enhancement of the luminescence intensity of the mixture on account of the superimposing of luminescence.
Spectrum-fingerprint anti-counterfeiting fiber with double luminous centers was tentatively prepared using , , and PAN powder as main raw materials by wet spinning. The microstructure and spectral properties of the fiber were studied by means of scanning electron microscope (SEM), x-ray diffractometer (XRD), and a fluorescence spectrophotometer. The results showed that the two rare-Earth luminous materials were randomly dispersed on the interior and surface of the fiber. Due to the spinning process, the luminescent materials were agglomerated in fiber, and there were many voids in the fiber. Compared with pure rare-Earth luminous materials, the emission wavelength of the spectrum-fingerprint anti-counterfeiting fiber has no obvious shift, but the addition proportion and amount of two rare-Earth luminous materials have great influence on the spectral curve of the fiber. This fiber with two luminous centers maintains the basic characteristics of spectrum-fingerprint anti-counterfeiting fiber and is a new, to the best of our knowledge, type of anti-counterfeiting fiber with high anti-counterfeiting application potential.