The mesoporous zirconia/alumina composites were synthesized via a sol–gel method, followed by heat treatment at 500 °C for 5 h. The effect of the ZrO2/Al2O3 ratio on the structural and textural properties of the obtained composites was explored. Sorption analysis has confirmed that all samples have a mesoporous structure whose parameters (SBET, Vp and Dmax) strongly depend on the ZrO2/Al2O3 ratio. The XRD pattern of composites has shown that the addition of zirconia disrupts the crystallinity of alumina. The composites with higher zirconia content (50% ZrO2 and 67% ZrO2) are characterized by peaks related only to the zirconia phase. UV/Vis diffuse reflection spectra of all samples revealed that composites have more intensive absorption compared to pure oxides for wavelengths larger than 250 nm and similar band gaps. Photoluminescence measurements showed presence of defects in all samples, which are responsible for photocatalytic activity. All samples showed significant adsorption/photocatalytic efficacy for the removal/degradation of 2,4,6 -trichlorophenol (TCP). Results obtained using HPLC and TOC techniques showed that between 70 and 80% of the initial TCP concentration was removed/degraded after 4 h of illumination. These results were corelated with flat, conduction and valence band potentials of synthesized pure and binary oxides, calculated using Mott–Schottky plots.
30 December 2024 in Materials Chemistry and Physics
A statistical design was used to investigate the effect of various processing conditions on the structure of sol-gel derived Mg(II) doped alumina. Six processing variables were selected based on the Plackett-Burman design: concentration of magnesium nitrate, time and temperature of alcohol evaporation, temperature and time of annealing and heating rate were changed at two levels. For every set of conditions, samples with different specific surface area and degree of crystallinity were obtained. Analysis of the results showed that annealing temperature , heating rate and concentration of magnesium nitrate were the main factors affecting average crystallite size of the predominant phase of alumina. In the case of the specific surface area, two of selected six variables had pronounced effect; however the temperature of annealing was more effective than others. The present results show that the proposed model that uses crystallite size as a response variables is preferable to further research.
Alumina powders, pure and doped with nickel, were synthetized by sol-gel method and calcined at 500, 900 and 1100?C in order to obtain mesoporous structures with a high specific surface area, well adapTab. to catalytic application. The characterization of samples was performed by XRD, EPR spectroscopy and electrochemical impedance spectroscopy (EIS). XRD analysis showed that the addition of Ni2+, as well as the annealing temperature, affects the structural properties of the obtained composites. EPR analysis revealed the traces of Fe3+ impurities, the presence of oxy defects in alumina and Ni2+ in tetrahedral position for samples calcined at 1100?C. The impedance of the Nafion/alumina modified GCE depended on combined effect of porous structure and surface properties of alumina samples. The electrochemical behavior of a glassy carbon electrode modified with Ni (II)-doped aluminas was studied in 0.5 M NaOH solution, with and without methanol. The electrochemical activity of nickel-doped alumina composites was dictated by the amount of present NiO impurity.
The problem of water pollution by various xenobiotics has gained a lot of interest due to their persistence, bioaccumulation potential, and toxic effects on ecosystems and humans. Electrochemical sensors offer a rapid, sensitive, and cost-effective method for on-site monitoring. In this research, an electrochemical sensor for xenobiotics based on a biochar–alumina composite is developed. The biochar–alumina composites were obtained by the air-limited pyrolysis of oak sawdust in the presence of alumina. Two types of alumina were mixed with oak sawdust in three ratios and subjected to thermal treatment. The resulting composites were characterized by SEM, N2 adsorption isotherm, XRD, and electrochemical characterization. The detection of the herbicide pendimethalin and the antibiotic ciprofloxacin was investigated, and the composite with the optimal biochar/alumina ratio was selected for each of the xenobiotics studied. A linear current response was obtained for pendimethalin in the concentration range 0.7 μM to 70.0 μM with an LOD of 0.5 μM. A linear current response was obtained for ciprofloxacin in the concentration range 1.6 μM to 55.4 μM with an LOD of 0.63 μM. A comparison of the characterization results with the electroanalytical performance implied the importance of the hydrophobic/hydrophilic nature of the electrode surface for detecting the analyte under investigation.