Bhagyashree Mishra

Ms. Bhagyashree Mishra


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2020 in Molecules
Verified
Journal Article
Open access
PDF file
MJMohi Uddin Jewel
Mohi Uddin Jewel
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
BMBhagyashree Mishra
Bhagyashree Mishra
MCMaggie Chen
Maggie Chen
Fully inkjet-printed device fabrication is a crucial goal to enable large-area printed electronics. The limited number of two-dimensional (2D) material inks, the bottom-gated structures, and the low current on/off ratio of thin-film transistors (TFTs) has impeded the practical applications of the printed 2D material TFTs. In the search for TFTs with high current ratios, we introduce a stable and efficient method of nitrogen-doped graphene (NDG) ink preparation for inkjet printing by liquid-phase exfoliation. The NDG thin film is print-stacked with molybdenum disulfide (MoS2) by multiple printing passes to construct a MoS2–NDG stack. We demonstrate top-gated fully inkjet-printed MoS2–NDG transistors with silver drain, source, and gate electrodes, and a barium titanate (BaTiO3) dielectric. A 100% inkjet-printed MoS2–NDG vertical 2D active heterostructure layer transistor with a current on/off ratio of 1200 is exhibited. The results may lead towards the development of all-printed 2D material-based transistor switches.

22 February 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
CHChandan Qumar Howlader
Chandan Qumar Howlader
BMBhagyashree Mishra
Bhagyashree Mishra
MCMaggie Yihong Chen
Maggie Yihong Chen
Polyvinyl Alcohol (PVA) is a promising polymer due to its high solubility with water, availability in low molecular weight, having short polymer chain, and cost-effectiveness in processing. Printed technology is gaining popularity to utilize processible solution materials at low/room temperature. This work demonstrates the synthesis of PVA solution for 2.5% w/w, 4.5% w/w, 6.5% w/w, 8.5% w/w and 10.5% w/w aqueous solution was formulated. Then the properties of the ink, such as viscosity, contact angle, surface tension, and printability by inkjet and aerosol jet printing, were investigated. The wettability of the ink was investigated on flexible (Kapton) and non-flexible (Silicon) substrates. Both were identified as suitable substrates for all concentrations of PVA. Additionally, we have shown aerosol jet printing (AJP) and inkjet printing (IJP) can produce multi-layer PVA structures. Finally, we have demonstrated the use of PVA as sacrificial material for micro-electro-mechanical-system (MEMS) device fabrication. The dielectric constant of printed PVA is 168 at 100 kHz, which shows an excellent candidate material for printed or traditional transistor fabrication.

1 January 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
AAAbid Ahmad
Abid Ahmad
BMBhagyashree Mishra
Bhagyashree Mishra
Andrew FoleyAndrew Foley
Andrew Foley
LWLeslie Wood
Leslie Wood
MCMaggie Chen
Maggie Chen
The paper is focused on the development and optimization of strontium ferrite nanomaterial and photosintered flexible thin films. These magnetic thin films are characterized with direct current (DC) and high frequency measurements. For photosintered strontium ferrite samples, we achieved relative complex permeability of about 29.5-j1.8 and relative complex permittivity of about 12.9-j0.3 at a frequency of 5.9 GHz.

19 December 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
BMBhagyashree Mishra
Bhagyashree Mishra
MCMaggie Chen
Maggie Chen
The printability of reliable gate dielectrics and their influence on the stability of the device are some of the primary concerns regarding the practical application of printed transistors. Major ongoing research is focusing on the structural properties of dielectric materials and deposition parameters to reduce interface charge traps and hysteresis caused by the dielectric–semiconductor interface and dielectric bulk. This research focuses on improving the dielectric properties of a printed polymer material, cross-linked polyvinyl phenol (crPVP), by optimizing the cross-linking parameters as well as the aerosol jet printability. These improvements were then applied to the fabrication of completely printed carbon nanotube (CNT)-based thin-film transistors (TFT) to reduce the gate threshold voltage (Vth) and hysteresis in Vth during device operation. Finally, a fully aerosol-jet-printed CNT device was demonstrated using a 2:1 weight ratio of PVP with the cross-linker poly(melamine-co-formaldehyde) methylated (PMF) in crPVP as the dielectric material. This device shows significantly less hysteresis and can be operated at a gate threshold voltage as low as −4.8 V with an on/off ratio of more than 104.