Fully inkjet-printed device fabrication is a crucial goal to enable large-area printed electronics. The limited number of two-dimensional (2D) material inks, the bottom-gated structures, and the low current on/off ratio of thin-film transistors (TFTs) has impeded the practical applications of the printed 2D material TFTs. In the search for TFTs with high current ratios, we introduce a stable and efficient method of nitrogen-doped graphene (NDG) ink preparation for inkjet printing by liquid-phase exfoliation. The NDG thin film is print-stacked with molybdenum disulfide (MoS2) by multiple printing passes to construct a MoS2–NDG stack. We demonstrate top-gated fully inkjet-printed MoS2–NDG transistors with silver drain, source, and gate electrodes, and a barium titanate (BaTiO3) dielectric. A 100% inkjet-printed MoS2–NDG vertical 2D active heterostructure layer transistor with a current on/off ratio of 1200 is exhibited. The results may lead towards the development of all-printed 2D material-based transistor switches.
We report a comparative spectroscopic study on the thin films of epitaxial aluminum nitride (AlN) on basal plane sapphire (Al2O3) substrates grown in hydrogen (H2) and nitrogen (N2) gas reaction environments. AlN films of similar thicknesses (~3.0 µm) were grown by metal-organic chemical vapor deposition (MOCVD) for comparison. The impact of the gas environment on the AlN epilayers was characterized using high-resolution X-ray diffraction (HR-XRD), X-ray photoelectron spectroscopy (XPS), Raman scattering (RS), secondary ion mass spectroscopy (SIMS), cathodoluminescence (CL), atomic force microscopy (AFM), and scanning electron microscopy (SEM). The study showed that AlN layers grown in a N2 environment have 50% less stress (~0.5 GPa) and similar total dislocation densities (~109/cm2) as compared to the films grown in a H2 environment. On the other hand, AlN films grown in a H2 gas environment have about 33% lesser carbon and 41% lesser oxygen impurities than films grown in a N2 growth environment. The possible mechanisms that influenced the structural quality and impurity incorporation for two different gas environments to grow AlN epilayers in the MOCVD system on sapphire substrates were discussed.
We report on 193 nm excimer laser-based liftoff (LLO) of Al0.26Ga0.74N/GaN high electron mobility transistors (HEMTs) with thick (t > 10 μm) AlN heat spreading buffer layers grown over sapphire substrates. The use of the thick AlN heat spreading layer resulted in thermal resistance ( ) of 16 K mm/W for as-fabricated devices on sapphire, which is lower than the value of ∼25–50 K mm/W for standard HEMT structures on sapphire without the heat-spreaders. Soldering the LLO devices onto a copper heat sink led to a further reduction of to 8 K mm/W, a value comparable to published measurements on bulk SiC substrates. The reduction in by LLO and bonding to copper led to significantly reduced self-heating and drain current droop. A drain current density as high as 0.9 A/mm was observed despite a marginal reduction of the carrier mobility (∼1800 to ∼1500 cm2/V s). This is the highest drain current density and mobility reported to-date for LLO AlGaN/GaN HEMTs.
We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal–organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of β-Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (01) orientation peaks of β-Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 × 1018 cm−3 and mobility of ~770 cm2V−1s−1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance–voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 × 1013 cm−2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV−1. A significant reduction in leakage current from ~10−4 A/cm2 for HFET to ~10−6 A/cm2 for MOSHFET was observed well beyond pinch-off in the off-stage at -20 V applied gate voltage. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.
Ultrawide bandgap (UWBG) AlGaN-channel metal-oxide-semiconductor heterostructure field-effect transistors (MOSHFETs) with a ZrO2 gate dielectric achieve peak current in excess of 0.4 A/mm and current ON/OFF ratios >106 with subthreshold swings as low as 110 mV/decade. These devices have strong potential for use in power and radio frequency electronics or as true solar-blind photodetectors. In this work, we present the photoresponse analysis in UWBG AlGaN MOSHFETs. Persistent photoconductivity with the decay time above 10 minutes can be quenched by illuminating with strong UV light at 365 nm and 254 nm, suggesting deep traps to be responsible for this behavior. Upon correlating the optical response under various illumination conditions with cathodoluminescence of these devices, we identified two key trap levels at ∼2.48 ± 0.14 eV and 3.76 ± 0.06 eV, controlling the slow response time. By depth-profiling using cathodoluminescence, these traps are identified to be at the AlN/AlGaN interface at the back of the device, due to partial relaxation from the lattice mismatch between AlN and Al0.4Ga0.6N.