Mahmuda Akter Monne

Mrs. Mahmuda Akter Monne

Doctoral Candidate
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2018 in International Journal of Antennas and Propagation
Verified
Journal Article
Open access
PDF file
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
XLXing Lan
Xing Lan
MCMaggie Chen
Maggie Chen
Flexible antennas offer many advantages for communication, radar, RF identification, and energy harvesting applications. A review on the material selection and fabrication process of flexible antennas is presented since these aspects are critical to the antenna’s overall electrical and mechanical performance. A number of different material and fabrication techniques are reviewed in detail for different types of antennas. In addition, experimental results are also discussed for these antennas, which further underlines the importance of material selection and the various fabrication processes.

18 September 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
PGPeter Grubb
Peter Grubb
HSHarold Stern
Harold Stern
Harish SubbaramanHarish Subbaraman
Harish Subbaraman
RCRay Chen
Ray Chen
MCMaggie Chen
Maggie Chen
Low-cost and conformal phased array antennas (PAAs) on flexible substrates are of particular interest in many applications. The major deterrents to developing flexible PAA systems are the difficulty in integrating antenna and electronics circuits on the flexible surface, as well as the bendability and oxidation rate of radiating elements and electronics circuits. In this research, graphene ink was developed from graphene flakes and used to inkjet print the radiating element and the active channel of field effect transistors (FETs). Bending and oxidation tests were carried out to validate the application of printed flexible graphene thin films in flexible electronics. An inkjet-printed graphene-based 1 × 2 element phased array antenna was designed and fabricated. Graphene-based field effect transistors were used as switches in the true-time delay line of the phased array antenna. The graphene phased array antenna was 100% inkjet printed on top of a 5 mil flexible Kapton® substrate, at room temperature. Four possible azimuth steering angles were designed for −26.7°, 0°, 13°, and 42.4°. Measured far-field patterns show good agreement with simulation results.

28 February 2020 in Molecules
Verified
Journal Article
Open access
PDF file
MJMohi Uddin Jewel
Mohi Uddin Jewel
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
BMBhagyashree Mishra
Bhagyashree Mishra
MCMaggie Chen
Maggie Chen
Fully inkjet-printed device fabrication is a crucial goal to enable large-area printed electronics. The limited number of two-dimensional (2D) material inks, the bottom-gated structures, and the low current on/off ratio of thin-film transistors (TFTs) has impeded the practical applications of the printed 2D material TFTs. In the search for TFTs with high current ratios, we introduce a stable and efficient method of nitrogen-doped graphene (NDG) ink preparation for inkjet printing by liquid-phase exfoliation. The NDG thin film is print-stacked with molybdenum disulfide (MoS2) by multiple printing passes to construct a MoS2–NDG stack. We demonstrate top-gated fully inkjet-printed MoS2–NDG transistors with silver drain, source, and gate electrodes, and a barium titanate (BaTiO3) dielectric. A 100% inkjet-printed MoS2–NDG vertical 2D active heterostructure layer transistor with a current on/off ratio of 1200 is exhibited. The results may lead towards the development of all-printed 2D material-based transistor switches.

22 February 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
CHChandan Qumar Howlader
Chandan Qumar Howlader
BMBhagyashree Mishra
Bhagyashree Mishra
MCMaggie Yihong Chen
Maggie Yihong Chen
Polyvinyl Alcohol (PVA) is a promising polymer due to its high solubility with water, availability in low molecular weight, having short polymer chain, and cost-effectiveness in processing. Printed technology is gaining popularity to utilize processible solution materials at low/room temperature. This work demonstrates the synthesis of PVA solution for 2.5% w/w, 4.5% w/w, 6.5% w/w, 8.5% w/w and 10.5% w/w aqueous solution was formulated. Then the properties of the ink, such as viscosity, contact angle, surface tension, and printability by inkjet and aerosol jet printing, were investigated. The wettability of the ink was investigated on flexible (Kapton) and non-flexible (Silicon) substrates. Both were identified as suitable substrates for all concentrations of PVA. Additionally, we have shown aerosol jet printing (AJP) and inkjet printing (IJP) can produce multi-layer PVA structures. Finally, we have demonstrated the use of PVA as sacrificial material for micro-electro-mechanical-system (MEMS) device fabrication. The dielectric constant of printed PVA is 168 at 100 kHz, which shows an excellent candidate material for printed or traditional transistor fabrication.

25 February 2016 in RSC Advances
Verified
Journal Article
Closed access
PDF file
ZWZhuo Wang
Zhuo Wang
ZLZhihong Liu
Zhihong Liu
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
SWShuangyue Wang
Shuangyue Wang
QYQingkai Yu
Qingkai Yu
MCMaggie Chen
Maggie Chen
Graphene flakes (<5 layers) are produced by CVD and electrochemical delamination. Isolated graphite without sintering, cu powder with graphene is separated water.

28 March 2018 in International Journal of Antennas and Propagation
Verified
Journal Article
Open access
PDF file
Mahmuda Akter MonneMahmuda Akter Monne
Mahmuda Akter Monne
XLXing Lan
Xing Lan
CZChunbo Zhang
Chunbo Zhang
MCMaggie Chen
Maggie Chen
This paper presents a fully inkjet-printed flexible MEMS switch for phased-array antennas. The physical structure of the printed MEMS switch consists of an anchor with a clamp-clamp beam, a sacrificial layer, and bottom transmission lines. 5-mil Kapton® polyimide film is used as a flexible substrate material. Two different types of conductive ink PEDOT : PSS from Sigma Aldrich and silver nanoparticle ink from NovaCentrix are used for the fabrication of different printed layers. Layer-by-layer fabrication process and material evaluation are illustrated. Layer characterization is done with respect to critical thickness and resistance using 2D/3D material analysis. Fujifilm Dimatix Material Printer (DMP-2800) is used for fabrication, and KLA-Tencor (P-7) profiler is used for 2D and 3D analysis of each layer. The MEMS switch has a low actuation voltage of 1.2 V, current capacity of 0.2195 mA, a current on-off ratio of 2195 : 1, and an RF insertion loss of 5 dB up to 13.5 GHz. Printed MEMS switch technology is a promising candidate for flexible and reconfigurable phased-array antennas and other radio frequency (RF) and microwave frequency applications.