Leila Ghorbani

Ms. Leila Ghorbani

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
LGLeila Ghorbani
Leila Ghorbani
Daniela CascheraDaniela Caschera
Daniela Caschera
BSBabak Shokri
Babak Shokri
Hydrophobic and oleophilic Si-based cotton fabrics have recently gained a lot of attention in oil/water separation due to their high efficiency. In this study, we present the effect of O2 plasma pre-treatment on the final properties of two Si-based cotton membranes obtained from dip coating and plasma polymerization, using polydimethylsiloxane (PDMS) as starting polymeric precursor. The structural characterizations indicate the presence of Si bond on both the modified cotton surfaces, with an increase of the carbon bond, assuring the success in surface modification. On the other hand, employing O2 plasma strongly changes the cotton morphology, inducing specific roughness and affecting the hydrophobicity durability and separation efficiency. In particular, the wettability has been retained after 20 laundry tests at 40 °C and 80 °C, and, for separation efficiency, even after 30 cycles, an improvement in the range of 10–15%, both at room temperature and at 90 °C can be observed. These results clearly demonstrate that O2 plasma pre-treatment, an eco-friendly, non-toxic, solvent-free, and one-step method for inducing specific functionalities on surfaces, is very effective in enhancing the oil/water separation properties for Si-based cotton membranes, especially in combination with plasma polymerization procedure for Si-based deposition.

17 April 2025 in ACS Applied Electronic Materials
Verified
Journal Article
Closed access
LGLeila Ghorbani
Leila Ghorbani
SKShreya Kundu
Shreya Kundu
JLJie Li
Jie Li
SKSouvik Kundu
Souvik Kundu
SMShankha Mukherjee
Shankha Mukherjee
SGStefan De Gendt
Stefan De Gendt

22 November 2024 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
SKShreya Kundu
Shreya Kundu
LGLeila Ghorbani
Leila Ghorbani
FLFrederic Lazzarino
Frederic Lazzarino
SGStefan De Gendt
Stefan De Gendt
Atomic layer etching (ALE) continues to garner wide attention as a technique for controlled patterning of different materials.1,2 However, a substantial amount of these studies are carried out on blanket films. It is therefore pivotal to investigate the feasibility of ALE for patterning high-density features as it exhibits the potential to be the preferred etching method for novel materials in the semiconductor industry. This talk will focus on the impact of ALE in the patterning of complex metal oxides like InGaZnO and MgZnO. These metal oxides are potential contenders as channel materials in high-performing transistors for memory and compute applications.3 Therefore, several critical criteria need to be followed when ALE conditions are being defined. The channel needs to be patterned with minimal physical and chemical damage such that there is little or no impact on the mobility parameters of the channel. The etching process should not induce redeposition onto the hard mask which also acts as a top contact in an integrated stack within the chip. In the case of InGaZnO, ALE-based patterning down to pitch 36 nm will be discussed in a systematic fashion.4 At such scaled pitches, it is observed that the etching challenges highlighted above cannot be resolved completely by ALE itself. Therefore, ALE in conjunction with other patterning approaches such as plasma pulsing needs to be employed to achieve satisfactory etching of the features at pitch 36 nm. On the other hand, when the metal oxide layer comprises a non-volatile element like Mg (in MgZnO), the etching mechanism tends to be both physical and chemical. In this case, it is still seen that the ALE approach provides a more controlled way of removing the layer without damaging the layer composition when compared to its conventional counterpart – reactive ion etching (RIE) at pitch 90 nm.5 REFERRENCES (1) Metzler, D.; Bruce, R. L.; Engelmann, S.; Joseph, E. A.; Oehrlein, G. S.; Fluorocarbon Assisted Atomic Layer Etching of SiO2 Using Cyclic Ar/C4F8 Plasma. J. Vac. Sci. Technol. A 2014, 32, 020603. (2) Metzler, D.; Li, C.; Engelmann, S.; Bruce, R. L.; Joseph, E. A.; Oehrlein, G. S.; Fluorocarbon Assisted Atomic Layer Etching of SiO2 and Si Using Cyclic Ar/C4F8 and Ar/CHF3 plasma. J. Vac. Sci. Technol. A 2016, 34, 01B101. (3) Belmonte, A.; Oh, H.; Rassoul, N.; Donadio, G. L.; Mitard, J.; Dekkers, H.; Delhougne, R.; Subhechha, S.; Chasin, A.; van Setten, M. J.; Kljucar, L.; Mao, M.; Puliyalil, H.; Pak, M.; Teugels, L.; Tsvetanova, D.; Banerjee, K.; Souriau, L.; Tokei, Z.; Goux, L.; Kar, G. S.; Capacitor-Less, Long-Retention (>400s) DRAM Cell Paving the Way towards Low-Power and High-Density Monolithic 3D DRAM. 2020 IEEE International Electron Devices Meeting (IEDM) 2020, pp. 28.2.1-28.2.4. (4) Kundu, S.; Decoster, S.; Bezard, P.; Mehta, A. N.; Dekkers, H.; Lazzarino F.; High-Density Patterning of InGaZnO by CH4: a Comparative Study of RIE and Pulsed Plasma ALE. ACS Appl. Mater. Interfaces 2022, 14, 29, 34029–34039. (5) Ghorbani, L.; Kundu, S.; De Gendt, S.; Manuscript in preparation.

29 October 2025 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
LGLeila Ghorbani
Leila Ghorbani
SKSouvik Kundu
Souvik Kundu
APAlexandru Pavel
Alexandru Pavel
SMShankha Mukherjee
Shankha Mukherjee
AKAnastasiia Kruv
Anastasiia Kruv
SKShreya Kundu
Shreya Kundu

22 December 2023 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
LGLeila Ghorbani
Leila Ghorbani
SKShreya Kundu
Shreya Kundu
FLFrederic Lazzarino
Frederic Lazzarino
SGStefan De Gendt
Stefan De Gendt
Magnesium Zinc Oxide (MgZnO) is a novel metal alloy being considered for advanced memory applications. When used as a dielectricum in transistors in dynamic random-access memory (DRAM) [1,2] or core elements in resistive random-access memory (RRAM) [3,4], MgZnO exhibits the potential to display low cutoff current [Ioff], high mobility [3], and low processing temperature [1]. Therefore, minimal damage-inducing patterning of the alloy for use in electrical nanoscale devices is needed. During the etching process, MgZnO film may be chemically and physically damaged, impacting its electrical performance. Changes in chemical composition and diffusion of etchants into the material are some types of chemical damages observed during etching. These can impact carrier mobility within the material. Physical damage consists of modified roughness, profile distortion, and redeposition on the pattern sidewalls. These are all critical issues because carrier transport in transistor channels is significantly affected by interface roughness between the channel and gate insulator [5]. The etch process developed should preserve the chemical composition and roughness in MgZnO and provide good selectivity when patterning other layers of the stack and hard mask (HM). There are three methods for dry etching consisting of physical, chemical, and physical-chemical mechanisms [6]. Pure physical etching is not selective and pure chemical etching can be isotropic. Reactive ion etching (RIE) is used in this study to generate an etching mechanism that can provide an optimal combination of chemical and physical etching [6]. In this work, we carried out the etch investigation of MgZnO film using an RIE-transformer coupled plasma (TCP) system. 10 nm MgZnO films are deposited on a 50 nm SiO2 layer/Si substrate. The impact of different gas mixing ratios, RF power, DC substrate bias, and process pressure are studied. The etching of MgZnO thin films is carried out using Cl2/CH4/Ar mixture. Cl2 increases chemical reactivity by creating MgCl2 [7] and ZnCl2 [8] by-products that are easier to remove than breaking Mg-O and Zn-O bonds from the films. Moreover, the addition of CH4 produces organometallic volatile etch by-product – Zn (CH3)2 (boiling point: 46°C) [8]. Therefore, MgZnO is to be etched partly by physical and chemical mechanisms. These hypotheses are studied in detail by carrying out in-depth X-ray photoelectron spectroscopy (XPS) based composition analysis on individual ZnO and MgO surfaces subjected to the aforementioned chemistry (Fig.1(a, b)). In addition, by increasing the voltage and power, the etching performance of MgZnO is further improved due to increasing ion energy and the presence of more active species in the plasma via higher dissociation and ionization, respectively (Fig.1(c, d)). These investigations should enable a more systematic patterning study of MgZnO-based features at different scaled dimensions and densities. References [1] J. Hwang, et al, Materials Science and Engineering: B, 266 (2021) 115063. [2] J. Y. Li et al. Materials, 10(2) (2017) 126. [3] Z. Zhang et al., Materialia, 15 (2021) 101001. [4] X. Chen et al., Applied Physics Letters, 104 (2014) 043508. [5] M. Geiger et al., Advanced material interfaces, 7(10) (2020) 1902145. [6] S. J. Pearton, et al, Plasma processes and polymers, 2(1) (2005) 16-37. [7] K. H. Baik et al., Applied Surface Science, 183 (2001) 26-32. [8] J. S. Park et al., Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena, 21 (2003) 800. Figure 1

11 December 2025 in ACS Applied Nano Materials
Verified
Journal Article
Closed access
LGLeila Ghorbani
Leila Ghorbani
APAlexandru Pavel
Alexandru Pavel
HDHendrik F. W. Dekkers
Hendrik F. W. Dekkers
SGStefan De Gendt
Stefan De Gendt
SKShreya Kundu
Shreya Kundu