mostafa mahmoud oweis

Mr. mostafa mahmoud oweis

Mechanical engineering, King Fahd University of Petroleum and Minerals, Dhahran, Ash Sharqīyah, Saudi Arabia
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
MOmostafa mahmoud oweis
mostafa mahmoud oweis
SEShimaa El-Hadad
Shimaa El-Hadad
MSmahmoud sherif
mahmoud sherif
KIKhaled M Ibrahim
Khaled M Ibrahim
AFAhmed I. Z. Farahat
Ahmed I. Z. Farahat
Helmi AttiaHelmi Attia
Helmi Attia
A comparative study was conducted for the machining of two α/β titanium alloys, namely Ti-6Al-4V (Ti64) and Ti-6Al-7Nb (Ti67), using wire electric discharge machining (WEDM). The influence of cutting speed and cutting mode on the machined surfaces in terms of surface roughness (Ra), recast layer (RL), and micro-hardness have been evaluated. Rough cut (RC) mode at a cutting speed of 50 µm/s resulted in thermal damage; Ra was equal to 5.68 ± 0.44 and 4.52 ± 0.35 µm for Ti64 and Ti67, respectively. Trim-cut mode using seven cuts (TRC-VII) at the same speed decreased the Ra to 1.02 ± 0.20 µm for Ti64 and 0.92 ± 0.10 µm for Ti67. At 100 µm/s, Ra reduced from 2.34 ± 0.28 µm to 0.88 ± 0.12 µm (Ti64), and from 1.42 ± 0.15 µm to 0.90 ± 0.08µm (Ti67) upon changing from TRC-III to TRC-VII. Furthermore, a thick recast layer of 30 ± 0.93 µm for Ti64 and 14 ± 0.68 µm for Ti67 was produced using the rough mode, while TRC-III and TRC-VII modes produced layers of 12 ± 1.31 µm and 5 ± 0.72 µm for Ti64 and Ti67, respectively. Moreover, rough cut and trim cut modes of WEDM played a significant role in promoting the surface hardness of Ti64 and Ti67. By employing the Response Surface Methodology, it was found that the machining mode followed by cutting speed and the interaction between them are the most influential parameters on surface roughness. Finally, mathematical models correlating machining parameters to surface roughness were successfully developed. The results strongly promote the trim-cut mode of WEDM as a promising machining route for two-phase titanium alloys.

21 December 2022 in International Journal of Materials Technology and Innovation
Verified
Journal Article
Closed access
MOmostafa mahmoud oweis
mostafa mahmoud oweis
SEShimaa El-Hadad
Shimaa El-Hadad
HAHelmi Attia
Helmi Attia
Titanium alloys, due to their distinctive properties, are used in a wide range of modern applications. However, because these alloys are challenging to machine using traditional methods, nonconventional processes are more often utilized. One of the unique thermal machining techniques that offers an effective choice for creating components with the highest degree of dimensional accuracy and surface finish quality from difficult-to-machine materials such as titanium alloys is Wire Electrical Discharge Machining (WEDM). . In the first part of this paper try to highlight the research trends in WEDM on finding the relationships among various process parameters, such as pulse on time, pulse off time, servo voltage, peak current, dielectric flow rate, cutting speed, wire tension, and machining modes, which have a crucial impact on a variety of process responses, such as material removal rate (MRR), surface roughness (Ra), sparking gap (Kerf width), and wire wear ration (WWR), as well as surface integrity. The second part of article also discusses various modeling, simulation, and optimization technique for monitoring process parameters to investigate the feasibility of various control practices for achieving the best machining conditions. The final part of the paper discusses these developments and includes some recommendations about the possible trends for future WEDM researches.