Numerical prediction of cavitation erosion is a great scientific and technological challenge. In the past, many attempts were made—many successful. One of the issues when a comparison between a simulation and erosion experiments is made, is the great difference in time scale. In this work, we do not attempt to obtain quantitatively accurate predictions of erosion process but concentrate qualitatively on cavitation mechanisms with quantitative prediction of pressure pulses which lead to erosion. This is possible, because of our recent experimental work on simultaneous observation of cavitating flow and cavitation erosion by high speed cameras. In this study, the numerical simulation was used to predict details of the cavitation process during the vapor collapse phase. The fully compressible, cavitating flow simulations were performed to resolve the formation of the pressure waves at cavitation collapse. We tried to visualize the mechanisms and dynamics of vapor structures during collapse phase at the Venturi geometry. The obtained results show that unsteady Reynolds-averaged Navier–Stokes (URANS) simulation of cavitation is capable of reproducing four out of five mechanisms of cavitation erosion, found during experimental work.

The presented paper aims to study the influence of mineral diesel fuel and synthetic Gas-To-Liquid fuel (GTL) on the injection process, fuel flow conditions, and cavitation formation in a modern common-rail injector. First, the influence on injection characteristics was studied experimentally using an injection system test bench, and numerically using the one-dimensional computational program. Afterward, the influence of fuel properties on internal fuel flow was studied numerically using a computational program. The flow inside the injector was considered as multiphase flow and was calculated through unsteady Computational Fluid Dynamics simulations using a Eulerian–Eulerian two-fluid approach. Finally, the influence of in-cylinder back pressure on the internal nozzle flow was studied at three distinctive back pressures. The obtained numerical results for injection characteristics show good agreement with the experimental ones. The results of 3D simulations indicate that differences in fuel properties influence internal fuel flow and cavitation inception. The location of cavitation formation is the same for both fuels. The cavitation formation is triggered regardless of fuel properties. The size of the cavitation area is influenced by fuel properties and also from in-cylinder back pressure. Higher values of back pressure induce smaller areas of cavitation and vice versa. Comparing the conditions at injection hole exit, diesel fuel proved slightly higher average mass flow rate and velocities, which can be attributed to differences in fluid densities and viscosities. Overall, the obtained results indicate that when considering the injection process and internal nozzle flow, GTL fuel can be used in common-rail injection systems with solenoid injectors.

Plastic is one of the most widely used materials worldwide. The problem with plastic arises when it becomes waste, which needs to be treated. One option is to transform plastic waste into synthetic fuels, which can be used as replacements or additives for conventional fossil fuels and can contribute to more sustainable plastic waste treatment compared with landfilling and other traditional waste management processes. Thermal and catalytic pyrolysis are common processes in which synthetic fuels can be produced from plastic waste. The properties of pyrolytic oil are similar to those of fossil fuels, but different additives and plastic stabilizers can affect the quality of these synthetic fuels. The quality of fuels and the permissible particle sizes and number density are regulated by fuel standards. Particle size in fuels is also regulated by fuel filters in vehicles, which are usually designed to capture particles larger than 4 μm. Problems can arise with the number density (quantity) of particles in synthetic fuels compared to that in fossil fuels. The present work is a numerical study of how particle size and number density (quantity) influence cavitation phenomena and cavitation erosion (abrasion) in common-rail diesel injectors. The results provide more information on whether pyrolysis oil (synthetic fuel) from plastic waste can be used as a substitute for fossil fuels and whether their use can contribute to more sustainable plastic waste treatments. The results indicate that the particle size and number density slightly influence cavitation phenomena in diesel injectors and significantly influence abrasion.

The presented paper addresses two significant issues of the present time. In general, the studies of the effect of synthetic fuels on cavitation formation and cavitation erosion prediction in the nozzle tip of common-rail diesel injectors were addressed. The first problem is plastic waste, which can have a significant negative environmental impact if not treated properly. Most plastic waste has high energy value, so it represents valuable material that can be used in resource recovery to produce various materials. One possible product is synthetic fuel, which can be produced using thermal and catalytic pyrolysis processes. The first issue addressed in the presented paper is the determination of fuel properties since they highly influence the fuel injection process, spray development, combustion, etc. The second is the prediction of cavitation development and cavitation erosion in a common-rail diesel injector when using pyrolytic oils from waste plastic. At first, pyrolytic oils from waste high- and low-density polyethylene were obtained using thermal and catalytic pyrolysis processes. Then, the obtained oils were further characterised. Finally, the properties of the obtained oils were implemented in the ANSYS FLUENT computational program and used in the study of the cavitation phenomena inside an injection nozzle hole. The cavitating flow in FLUENT was calculated using the Mixture Model and Zwart-Gerber-Belamri cavitation model. For the modelling of turbulence, a realisable k–ε model with Enhanced Wall Treatment was used, and an erosion risk indicator was chosen to compare predicted locations of cavitation erosion. The results indicate that the properties of the obtained pyrolytic oils have slightly lower density, surface tension and kinematic viscosity compared to conventional diesel fuel, but these minor differences influence the cavitation phenomenon inside the injection hole. The occurrence of cavitation is advanced when pyrolytic oils are used, and the length of cavitation structures is greater. This further influences the shift of the area of cavitation erosion prediction closer to the nozzle exit and increases its magnitude up to 26% compared to diesel fuel. All these differences have the potential to further influence the spray break-up process, combustion process and emission formation inside the combustion chamber.

Pollution of water by plastic contaminants has received increasing attention, owing to its negative effects on ecosystems. Small plastic particles propagate in water and can travel long distances from the source of pollution. In order to research the settling motion of particles in water flow, a small-scale experiment was conducted, whereby spherical plastic particles of varying diameters were released in an open-channel flow. Three approaches were investigated to numerically simulate the motion of particles. The numerical simulation results were compared and validated with experimental data. The presented methods allow for deeper insight into particle motion in fluid flow and could be extended to a larger scale to predict the propagation of mesoplastics in natural environments.