In recent years, the discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in a micro fluidized bed (MFB). The application of DEM in the simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely the particle circumstance-dependent drag model or PCDD model. Fast fluidization in an MFB of fine particles is simulated using DEM based on the PCDD model. Simulations indicate that the local structure in an MFB exhibits particle aggregation, which is a natural property of fast fluidization, forming a structure where a continuous dilute phase and dispersed concentrated phase coexist. There exists a strong effect of solid back-mixing in an MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a higher distribution pattern in the central region and a lower one in the sidewall region.
In chemical production processes, the most suitable operation regime for A-Type powders such as typical FCC particles is high-speed fast fluidization owing to their uniquely advantageous properties. Discrete element method (DEM) for modelling fast fluidization with A-Type powders has rarely been reported. How to appropriately select the DEM time step and the stiffness coefficient is one of the most critical problems for stable and accurate calculation. This article mainly discusses the effect of the stiffness coefficient and DEM time step on simulations of A-type FCC particles. In order to describe the effect of both parameters and their complex interaction, a dimensionless relative DEM time step is introduced. In total, nine cases with different numbers of relative time steps are adopted for modelling a microfluidized bed of A-Type FCC particles, the regime of which is proved to be fast fluidization. Results show that three bifurcations occur in all the simulations. Only the moderate relative time step possesses the capability of modelling the process of particle collision and thus predicts the right flow regime with asymmetric and heterogeneous typical fast fluidized structures. When the relative time step increases to large rank, simulations predict untrue fluidization regimes with symmetric and homogeneous structures. Moreover, both over-large and over-low relative time steps cause excessive particle overlap and thus a divergence of simulation. The further optimization of moderate relative DEM time step in relation to real particle property is unidentifiable and is thus an outstanding issue. That the range of the moderate relative time step is limited indicates that the common soft-sphere model is poor at modelling fast fluidization of A-Type particles. It is suggested that possible future work should be focused on improving the simulation frame and employing the molecular dynamics model to more appropriately deal with particle contact.
In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.