Noemi Faggio

Mrs. Noemi Faggio

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 May 2024 in Journal of Colloid and Interface Science
Verified
Journal Article
Open access
NFNoemi Faggio
Noemi Faggio
FOFederico Olivieri
Federico Olivieri
IBIrene Bonadies
Irene Bonadies
Gennaro GentileGennaro Gentile
Gennaro Gentile
Veronica AmbrogiVeronica Ambrogi
Veronica Ambrogi
Pierfrancesco CerrutiPierfrancesco Cerruti
Pierfrancesco Cerruti
Electroactive coatings for smart wearable textiles based on a furan bio-epoxy monomer (BOMF) crosslinked with isophorone diamine (IPD) and additivated with carbon nanotubes (CNTs) are reported herein. The effect of BOMF/IPD molar ratio on the curing reaction, as well as on the properties of the crosslinked resins was first assessed, and it was found that 1.5:1 BOMF/IPD molar ratio provided higher heat of reaction, glass transition temperature, and mechanical performance. The resin was then modified with CNT to prepare electrically conductive nanocomposite films, which exhibited conductivity values increased by eight orders of magnitude upon addition of 5 phr of CNTs. The epoxy/CNT nanocomposites were finally applied as coatings onto a cotton fabric to develop electrically conductive, hydrophobic and breathable textiles. Notably, the integration of CNTs imparted efficient and reversible electrothermal behavior to the cotton fabric, showcasing its potential application in smart and comfortable wearable electronic devices.

5 December 2022 in Polymers
Verified
Journal Article
Open access
PDF file
AMAngela Marotta
Angela Marotta
NFNoemi Faggio
Noemi Faggio
CBCosimo Brondi
Cosimo Brondi
The potential of furan-based epoxy thermosets as a greener alternative to diglycidyl ether of Bisphenol A (DGEBA)-based resins has been demonstrated in recent literature. Therefore, a deep investigation of the curing behaviour of these systems may allow their use for industrial applications. In this work, the curing mechanism of 2,5-bis[(oxiran-2-ylmethoxy)methyl]furan (BOMF) with methyl nadic anhydride (MNA) in the presence of 2-methylimidazole as a catalyst is analyzed. In particular, three systems characterized by different epoxy/anhydride molar ratios are investigated. The curing kinetics are studied through differential scanning calorimetry, both in isothermal and non-isothermal modes. The total heat of reaction of the epoxy resin as well as its activation energy are estimated by the non-isothermal measurements, while the fitting of isothermal data with Kamal’s autocatalytic model provides the kinetic parameters. The results are discussed as a function of the resin composition. The global activation energy for the curing process of BOMF/MNA resins is in the range 72–79 kJ/mol, depending on both the model used and the sample composition; higher values are experienced by the system with balanced stoichiometry. By the fitting of the isothermal analysis, it emerged that the order of reaction is not only dependent on the temperature, but also on the composition, even though the values range between 0.31 and 1.24.

13 February 2026 in Macromolecular Materials and Engineering
Verified
Journal Article
Open access
FOFederico Olivieri
Federico Olivieri
NFNoemi Faggio
Noemi Faggio
GPGiovanni Dal Poggetto
Giovanni Dal Poggetto
CSChiara Santillo
Chiara Santillo
RARoberto Avolio
Roberto Avolio
Gennaro GentileGennaro Gentile
Gennaro Gentile
In this work, we report the synthesis and characterization of non‐isocyanate polyhydroxyurethanes (PHUs) derived from resorcinol bis(cyclocarbonate) (RCC). The PHUs were obtained through polyaddition between RCC and two aliphatic diamines, namely isophoronediamine and Priamine 1075 (a commercial vegetal based diamine), selected due their eco‐friendliness, under mild conditions, without the use of toxic isocyanates and catalysts. The resulting materials were characterized by FTIR, NMR spectroscopy, GPC, DSC, and TGA to evaluate their chemical structure, molecular weight distribution, and thermal properties. Then, the processability of the synthesized PHUs was assessed and further functional characterizations, such as mechanical and viscoelastic properties, swelling and water contact angle tests, were performed. Finally, the RCC based PHUs were tested as potential adhesives for aluminium, polymer composite, and wood substrates. All the results highlight that RCC based PHUs are promising sustainable alternatives to fossil‐based polyurethanes.