The interfacial adhesion between carbon fibers (CFs) and a thermoplastic matrix is an important aspect that should be improved in manufacturing CF-reinforced thermoplastics with high strength and rigidity. In this study, the effects of a two-step surface treatment comprising electrochemical oxidation and silane treatment of the CF surface on the mechanical properties of CF/maleic anhydride-grafted polypropylene (MAPP) composites were confirmed. The surface characteristics of the treated CFs were analyzed via scanning electron microscopy, atomic force microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The tensile testing of a single CF and interfacial adhesion of the samples before and after the surface treatment were analyzed using a single-fiber testing machine and a universal testing machine. After the silane treatment, the roughness of the CF surface increased due to the formation of a siloxane network. In addition, the interfacial shear strength increased by ∼450% compared to that of the untreated CFs due to the covalent bond between the -NH2 end group of siloxane and MAPP. This two-step surface treatment, which can be performed continuously, is considered an effective method for improving the mechanical interface strength between the CF and polymer matrix.
In this study, natural fiber-reinforced polylactic acid (NFRP) composite materials were prepared by adding nucleating agents (NAs) and natural fiber (NF) to compensate for the low thermal stability and brittleness of polylactic acid (PLA). The thermal stability of the fabricated composite material was investigated by differential scanning calorimetry and thermogravimetric analysis. In addition, the tensile modulus of elasticity according to the crystallinity of the composite was measured. The crystallinity of the PLA composite increased to ~700% upon the addition of the NA; thus, the thermal stability also increased. However, the changes in crystallinity and tensile modulus were insignificant when the concentration of the NA added was 4 wt.% or higher. The study demonstrates that the addition of NA and NF is effective in improving the thermal stability and mechanical properties of NFRP.
In this study, carbon nanotubes (CNTs) were grown under the same conditions as those of carbon fibers and glass fibers, and a comparative analysis was performed to confirm the potential of glass fibers with grown CNTs as electromagnetic interference (EMI) shielding materials. The CNTs were grown directly on the two fiber surfaces by a chemical vapor deposition process, with the aid of Ni particles loaded on them via a Ni-P plating process followed by heat treatment. The morphology and structural characteristics of the carbon and glass fibers with grown CNTs were analyzed using scanning electron microscopy–energy dispersive X-ray spectroscopy (SEM–EDS), X-ray diffraction (XRD), and X-ray photoelectron spectrometry (XPS), and the EMI shielding efficiency (EMI SE) of the directly grown CNT/carbon and glass fiber-reinforced epoxy matrix composites was determined using a vector-network analyzer. As the plating time increased, a plating layer serving as a catalyst formed on the fiber surface, confirming the growth of numerous nanowire-shaped CNTs. The average EMI SET values of the carbon fiber-reinforced plastic (CFRP) and glass fiber-reinforced plastic (GFRP) with grown CNTs maximized at approximately 81 and 40 dB, respectively. Carbon fibers with grown CNTs exhibited a significantly higher EMI SET value than the glass fiber-based sample, but the latter showed a higher EMI SET increase rate. This indicates that low-cost, high-quality EMI-shielding materials can be developed through the growth of CNTs on the surface of glass fibers.
In this study, the effects of polyimide (PI) content and postcuring on thermal and mechanical properties in PI and epoxy (EP) blending systems were investigated. EP/PI (EPI) blending reduced the crosslinking density and improved the flexural and impact strength due to ductility. On the other hand, in the postcuring of EPI, the thermal resistance improved due to the increased crosslinking density and the flexural strength increased by up to 57.89% due to the enhanced stiffness, but the impact strength decreased by up to 59.54%. EPI blending induced the improvement in the mechanical properties of EP, and the postcuring process of EPI was shown to be an effective method to improve heat resistance. It was confirmed that EPI blending induces improvement in the mechanical properties of EP, and the postcuring process of EPI is an effective method for improving heat resistance.
Globally, the demand for carbon fiber-reinforced thermosetting plastics for various applications is increasing. As a result, the amount of waste from CFRPs is increasing every year, and the EU Council recommends recycling and reuse of CFRPs. Epoxy resin (EP) is used as a matrix for CFRPs, and amine hardeners are mainly used. However, no research has been conducted on recycling EP/4,4’-diaminodiphenyl sulfone (DDS)-based CFRP. In this study, the effect of steam and air pyrolysis conditions on the mechanical properties of re-cycled carbon fiber (r-CF) recovered from carbon fiber-reinforced thermosetting (epoxy/4,4′-diaminodiphenyl sulfone) plastics (CFRPs) was investigated. Steam pyrolysis enhanced resin degradation relative to N2. The tensile strength of the recovered r-CF was reduced by up to 35.12% due to oxidation by steam or air. However, the interfacial shear strength (IFSS) tended to increase by 9.18%, which is considered to be due to the increase in functional groups containing oxygen atoms and the roughness of the surface due to oxidation. The recycling of CFRP in both a steam and an air atmosphere caused a decrease in the tensile strength of r-CF. However, they were effective methods to recover r-CF that had a clean surface and increased IFSS.
In this study, a surface treatment process was introduced into the conventional dispersion process for preparing wet-laid nonwoven fabrics to improve their properties, using recycled carbon fibers (rCFs). The conventional binder solution was replaced with a solution containing different amounts of silane, and the changes in the fiber properties of the prepared nonwoven fabrics were examined after the addition of modified rCFs and polypropylene. FE-SEM analysis confirmed that a silane layer was formed on the rCF surface due to the formation of a siloxane network. FT-IR and XPS analyses further confirmed the presence of siloxane bonds and chemical modification of the rCF surface. When an optimal amount of silane content was used, the mechanical strength increased by 64% compared to untreated rCFs, owing to the improved molecular chain entanglement within the matrix. Our findings indicate that the simultaneous use of dispersion and a surface treatment can produce composites with excellent mechanical properties and improved processing and surface properties; thus, this method can be used to help upcycle rCFs, thereby expanding their applications.