In this study, natural fiber-reinforced polylactic acid (NFRP) composite materials were prepared by adding nucleating agents (NAs) and natural fiber (NF) to compensate for the low thermal stability and brittleness of polylactic acid (PLA). The thermal stability of the fabricated composite material was investigated by differential scanning calorimetry and thermogravimetric analysis. In addition, the tensile modulus of elasticity according to the crystallinity of the composite was measured. The crystallinity of the PLA composite increased to ~700% upon the addition of the NA; thus, the thermal stability also increased. However, the changes in crystallinity and tensile modulus were insignificant when the concentration of the NA added was 4 wt.% or higher. The study demonstrates that the addition of NA and NF is effective in improving the thermal stability and mechanical properties of NFRP.
Polyacrylonitrile (PAN) gels create significant obstacles in industrial fiber spinning by forming insoluble networks that compromise solution stability and uniformity. This study investigates the rheological properties of PAN/dimethyl sulfoxide (DMSO) solutions, examining how aging time, moisture content, and polymer concentration affect gelation behavior. Dynamic rheological analysis revealed that both physical and chemical crosslinks play crucial roles in gel formation, with gelation accelerating markedly when moisture content exceeds 3% and aging progresses. Under heat treatment at 80 °C, samples with increased moisture content demonstrated rapid transitions to solid-like states, indicating a critical moisture threshold for enhanced gelation kinetics. Additionally, reductions in polymer concentration disrupted physical crosslink density, thereby mitigating gel formation. These results underscore the importance of precisely controlling moisture and concentration parameters in PAN solutions to stabilize solution properties and minimize gel formation, thus enhancing process efficiency and quality in PAN-based carbon fiber production.
Ordered and disordered mesoporous structures were synthesized by a self-assembly method using a mixture of phenolic resin and petroleum-based mesophase pitch as the starting materials, amphiphilic triblock copolymer F127 as a soft template, hydrochloric acid as a catalyst, and distilled water as a solvent. Then, mesoporous carbons were obtained via autoclave method at low temperature (60 °C) and then carbonization at a relatively low temperature (600 °C), respectively. X-ray diffraction (XRD), small-angle X-ray scattering (SAXS), and transmission electron microscopy (TEM) analyses revealed that the porous carbons with a mesophase pitch content of approximately 10 wt% showed a highly ordered hexagonal mesostructure with a highly uniform pore size of ca. 5.0 nm. In addition, the mesoporous carbons prepared by self-assembly and low-temperature autoclave methods exhibited the amorphous or crystalline carbon structures with higher specific surface area (SSA) of 756 m2/s and pore volume of 0.63 cm3/g, depending on the synthesis method. As a result, mesoporous carbons having a high SSA were successfully prepared by changing the mixing ratio of mesophase pitch and phenolic resin. The electrochemical properties of as-obtained mesoporous carbon materials were investigated. Further, the OMC-meso-10 electrode delivered the maximum SC of about 241 F/g at an applied current density of 1 A/g, which was higher than those of the MC-10 (~104 F/g) and OMC-20 (~115 F/g).
Globally, the demand for single-use plastics has increased due to the rising demand for food delivery and household goods. This has led to environmental challenges caused by indiscriminate dumping and disposal. To address this issue, non-degradable plastics are being replaced with biodegradable alternatives. Polylactic acid (PLA) is a type of biodegradable plastic that has excellent mechanical properties. However, its applications are limited due to its low crystallinity and brittleness. Studies have been conducted to combat these limitations using carbon or inorganic nucleating agents. In this study, waste cement and PLA were mixed to investigate the effect of the hybrid inorganic nucleating agent on the crystallinity and mechanical properties of PLA. Waste cement accelerated the lamellar growth of PLA and improved its crystallinity. The results indicate that the flexural and impact strengths increased by approximately 3.63% and 76.18%, respectively.
Fine-denier silicone emulsions play an important role in the polyacrylonitrile (PAN) precursor treatment process by reducing surface tension and preventing fiber fusion during thermal stabilization and carbonization. These emulsions are typically prepared by dispersing polydimethylsiloxane (PDMS) polymers with various functional groups into water through different emulsification methods. In this study, two types of silicone emulsions—one prepared using a mechanical disperser and the other using a high-shear colloid mill—were manufactured on a pilot scale and systematically compared. Thermal aging was conducted at 50 °C and 70 °C for approximately one month, and changes in particle size, dispersion stability, and physicochemical properties were evaluated. The colloid-mill emulsification method produced smaller and more uniform silicone particles and exhibited superior thermal and dispersion stability relative to the mechanically dispersed emulsion. NMR relaxation, Turbiscan multiple light scattering, and viscosity measurements confirmed that the colloid-mill emulsion maintained a stable microstructure with minimal aggregation even under elevated-temperature storage. These results demonstrate that high-shear emulsification is an effective approach for producing fine-denier silicone emulsions with enhanced stability, making the colloid-mill method a more reliable and practical route for preparing silicone-based oiling agents used during PAN precursor processing in carbon fiber manufacturing.