This work introduces a new highly efficient heterostructure solar cell that shows the supremacy of the single-walled carbon nanotube as an absorber layer and platinum (Pt) as a back contact. This article focuses on the most important process: optimizing the thickness and acceptor concentration of the absorber layer. Another novel fact in this work is that minorities have been included as a replica of defects and the Auger hole/electron capture coefficient, and the variations in defects have been shown with some flawless contour plots. As the whole study has been carried out using a simulator, it might not be completely realistic, but it shows outcomes close to reality. In addition, the use of minorities takes this simulation work closer to the physical one. A contemporary model—Al/ZnO/TiO2/SWCNT/SnS/Pt—has been investigated in this work for efficient performance. At the end of tuning, the input parameters are set at thickness (W) = 1.5 µm, acceptor concentration (NA) = 1 × 1020 cm−3, and defects = 1 × 1015 cm−3. Under these optimum conditions, this model has shown outstanding outcomes: VOC = 1.04 V, JSC = 41.91 mA cm−2, FF = 72.12%, and η = 31.57%. Although an efficiency of 32.86% was achieved at NA = 1 × 1021 cm−3, it is difficult to keep the acceptor concentration high in reality. Hence, the optimum value of the acceptor concentration is considered at 1 × 1020 cm−3.
The involvement of assistive robot in every aspect of our life is immensely increasing in today's world. In this paper, a line following robot to assist an office is developed which can securely transfer hard copy of office file, tea snacks etc from one table to another inside an office autonomously as per user direction. Anybody can call the robot from any table by pressing a PUSH button. As a response of calling, the robot will come to the caller table following a path and a locker placed in the robot will be unlocked automatically. The caller then placed the file or any other materials in the locker and can direct the robot to another table by pressing another push button. The locker will not open until the robot reach at directed table to ensure the security. The robot also can detect obstacles and can produce alarm if someone stands in its path. The robot smoothly follows the path with the PID algorithm. The main components that are used to construct the robot are microcontroller, IR sensor module, RF Tx-Rx module, ultrasonic sensor, buzzer and DC motor. In every office there required a peon to transfer the files or other materials whereas they have to perform other tasks too. This robot can be useful to decrease the workload of office peons to involve him with more essential works.
This work presents a copper zinc tin sulfide (CZTS)-based solar cell structure (AI/ITO/C60/CZTS/SnS/Pt) with C60 as a buffer layer, developed using the SCAPS-1D simulator by optimizing each parameter to calculate the output. Optimizing the parameters, the acceptor concentration and thickness were altered from 6.0 × 1015 cm−3 to 6.0 × 1018 cm−3 and 1500 nm to 3000 nm, respectively. Although, in this simulator, we can tune the value for the acceptor concentration to 6.0 × 1022, higher doping might present an issue regarding adjustment in the physical experiment. Thus, tunable parameters need to be chosen according to the reliability of the experimental work. The defect density varied from 1.0 × 1014 cm−3 to 1.0 × 1017 cm−3 and the auger hole/electron capture coefficient was determined to be 1.0 × 10−26 cm6 s−1 for the maintenance of the minorities in theoretical to quasi-proper experimental measurements. Although the temperature was intended to be kept near room temperature, this parameter was varied from 290 K to 475 K to investigate the effects of the temperature on this cell. The optimization of the proposed structure resulted in a final acceptor concentration of 6.0 × 1018 cm−3 and a thickness of 3000 nm at a defect density of 1.0 × 1015 cm−3, which will help to satisfy the desired experimental performance. Satisfactory outcomes (VOC = 1.24 V, JSC = 27.03 mA/cm2, FF = 89.96%, η = 30.18%) were found compared to the previous analysis.
8 March 2026 in Journal of Environmental Chemical Engineering
The effects of Argon (Ar) on the Synthesis and Photocatalytic activities of monolayer Graphene under the flow of Methane (CH4) and Hydrogen (H2) gas has been studied. The Chemical Vapor Deposition (CVD) method was used to create a large area of monolayer graphene with features that meet the needs of a wide variety of applications. With this, the possibility of varying the dimensions of graphene by differing the argon gas while keeping other parameters constant was demonstrated. This helps with the ability to control the size and number of layers of graphene for different applications. Further, the photocatalytic activities of produced graphene were examined during CVD at various argon gas flow rates to observe their effects on the performances of graphene. The result shows that the synthesized graphene at Ar = 80 sccm is a monolayer with perfectly shaped edges. After exfoliation, the graphene obtained was properly formed with a large surface area, which helped achieve the results of higher photocatalytic activity.
The hybrid structure of Graphene and ZnO (Graphene/ZnO) is emerging as a novel material used to achieve the high performance of photocatalysis. In this study, we examined the ZnO characteristics that affect the photocatalytic activity of graphene/ZnO using a lamellar structure of graphene and ZnO thin films. Graphene samples were synthesized via chemical vapor deposition, and a typical wet process was applied to transfer them on sputter-deposited ZnO thin films with and without annealing. We confirmed that graphene-deposited ZnO demonstrated more efficient photocatalytic behavior toward the decomposition of methylene blue (as a model organic compound) with ordinary sputtered ZnO thin films. Again, ZnO thin films annealed at 1000 °C in an N2 gas atmosphere with graphene performed better than unannealed films. XRD analysis confirmed that pre-thermal treatment of a ZnO thin film promoted re-crystallization, which had less impact on the photocatalytic improvement. The attachment of graphene to the film is considered to contribute to the enhancement. Raman analysis revealed that the graphene coverage areas on the post-annealed ZnO increased by two times compared to that of an unannealed film where the unannealed film had a higher graphene layer. The results presented in this study demonstrate that an annealed ZnO thin film forms a better attachment with graphene, resulting in a larger graphene coverage area with fewer multilayers, which effectively improves the photocatalytic activity in composite structures.