Characterization of Softwood and Hardwood LignoBoost Kraft Lignins with Emphasis on their Antioxidant Activity

The valorization of lignins as renewable aromatic feedstock is of utmost importance in terms of the use of sustainable resources. This study provides a deductive approach towards market-oriented lignin-derived antioxidants by ascertaining the direct effect of different structural features of lignin on the reactivity of its phenolic OH groups in the radical scavenging reactions. The antioxidant activity of a series of compounds, modeling lignin structural units, was experimentally characterized and rationalized, using thermodynamic descriptors. The calculated O–H bond dissociation enthalpies (BDE) of characteristic lignin subunits were used to predict the modification pathways of technical lignins. The last ones were isolated by soda delignification from different biomass sources and their oligomeric fractions were studied as a raw material for modification and production of optimized antioxidants. These were characterized in terms of chemical structure, molecular weight distribution, content of the functional groups, and the antioxidant activity. The developed approach for the targeted modification of lignins allowed the products competitive with two commercial synthetic phenolic antioxidants in both free radical scavenging and stabilization of thermooxidative destruction of polyurethane films.

The barks of aspen (Populus tremula) and pine (Pinus sylvestris) are byproducts of wood processing, characterized by their low economic value. In the present study, microwave-assisted one-cycle water extraction was explored as a tool for the valorization of this biomass as a source of biologically active compounds. The microwave extractor of the original construction equipped with a pressurized extraction chamber and a condenser section was used. The microwave-assisted extraction (MAE), specially including dynamic dielectric heating up to 70 °C followed by 30 min of isothermal heating, promoted the isolation of salicin from aspen bark, allowing for the obtention of a two-times-higher free salicin concentration in water extracts (−14% vs. 7%) reached by multi-cycle accelerated solvent extraction (ASE), which is an advanced technique used as a reference. The MAE of pine bark with dynamic heating up to 90–130 °C, avoiding the isothermal heating step, allowed for the obtention of a 1.7-times-higher concentration of proantocyanidin dimers-tetramers, a 1.3-times-higher concentration of catechin and a 1.2-times-higher concentration of quinic acid in water extracts in comparison to a more time- and solvent-consuming ASE performed at the same temperature. The biological activity of the obtained extracts was characterized in terms of their ability to inhibit xahntine oxidase enzyme, which is a validated target for the therapeutic treatment of hyperuricemia.

European aspen (Populus tremula (L.) (Salicaceae)) bark is a promising raw material in multi-step biorefinery schemes due to its wide availability and higher content of secondary metabolites in comparison to stem wood biomass. The main objective of this study was to investigate the major cell wall component-enriched fractions that were obtained from aspen bark residue after extractives isolation, primarily focusing on integration of separated lignin fractions and cellulose-enriched bark residue into complex valorization pathways. The “lignin first” biorefinery approach was applied using mild organosolv delignification. The varying solvent systems and process conditions for optimal delignification of residual aspen bark biomass were studied using a response surface methodology approach. The conditions for maximum process desirability at which the highest amount of lignin-enriched fraction was separated were as follows: 20-h treatment time at 117 °C, butanol/water 4:1 (v/v) solvent system with solid to liquid ratio of 1 to 10. At optimal separation conditions, lignin-enriched fraction exhibited a higher content of β–O–4 linkages vs. C–C linkages content in its structure as well as a high amount of hydroxyl groups, being attractive for its further valorization. At the same time, the content of glucose in products of cellulose-enriched residue hydrolysis was 52.1%, increased from 10.3% in untreated aspen bark. This indicates that this fraction is a promising raw material for obtaining cellulose and fermentable glucose. These results show that mild organosolv delignification of extracted tree bark can be proposed as a novel biorefinery approach for isolation of renewable value-added products with various application potentials.

The hydrophilic extractives isolated from black alder (Alnus glutinosa) bark through hot water extraction were characterized as novel renewable macromonomers capable of forming polyurethane (PU) networks based on a commercial polyisocyanate, with partial or complete replacement of petroleum-derived polyol polyether. The bark-sourced bio-polyol mainly consists of the xyloside form of the diarylheptanoid oregonin, along with oligomeric flavonoids and carbohydrates, resulting in a total OH group content of 15.1 mmol·g⁻¹ and a molecular weight (M_n) of approximately 750 g∙mol⁻¹. The ³¹P NMR data confirmed a similar proportion of aliphatic OH and phenolic groups. Three-component PU compositions were prepared using polyethylene glycol (M_n = 400 g∙mol⁻¹), bio-polyol (up to 50%), and polymeric diphenylmethane diisocyanate, which were pre-polymerized in tetrahydrofuran (THF) solution with tin organic and tertiary amine catalysts. The resulting mixture was cast and subjected to thermal post-curing. Calculation and experimental data confirmed the crosslinking activity of the bark-sourced bio-polyol in PU, leading to an increase in glass transition temperature (Tg), a decrease in sol fraction yield upon leaching of cured PU networks in THF, a significant increase in Young’s modulus and tensile strength. The macromonomers derived from bark promoted char formation under high temperature and oxidative stress conditions, limiting heat release during macromolecular network degradation compared to bio-polyol-free PU. It was observed that amine catalysts, which are active in urethane formation with phenolic groups, promoted the formation of PU with higher Tg and modulus at tensile but with less limitation of heat liberation during PU macromolecular structure degradation. The high functionality of the bark-derived bio-polyol, along with the equal proportion of phenolic and aliphatic OH groups, allows for further optimization of PU characteristics using three variables: increasing the substitution extent of commercial polyethers, decreasing the NCO/OH ratio, and selecting the type of catalyst used.