Ryu-Gap Lim

Prof. Dr. Ryu-Gap Lim

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Wan-Soo KimWan-Soo Kim
Wan-Soo Kim
Md. Abu Ayub SiddiqueMd. Abu Ayub Siddique
Md. Abu Ayub Siddique
YKYong-Joo Kim
Yong-Joo Kim
YJYeon-Jun Jung
Yeon-Jun Jung
Seung-Min BaekSeung-Min Baek
Seung-Min Baek
RLRyu-Gap Lim
Ryu-Gap Lim
This study was focused on the stability analysis of the self-propelled radish harvester. A 3D simulation model was developed using RecurDyn and used to analyze the rollover angle. The rollover angle of the original radish harvester was analyzed and checked to see if it satisfied the standard overturning angle (i.e., 30°). To improve it, three simulated weights (50, 100, and 150 kg) were added to three positions (front, center, and rear). The rollover angle of the radish harvester was slightly less than the criterion angle at a deflection angle of 180°. This issue was solved by attaching an additional weight to the front with a deflection angle of 180 degrees. In particular, when an additional weight of 50 kg was attached to the front or an additional weight of 150 kg was attached to the center or rear, the criterion angle range satisfied all conditions. In conclusion, it is feasible that the self-propelled radish harvester prototype could satisfy the criterion angle with the additional load and could be applied to field agriculture.

4 October 2022 in Agriculture
Verified
Journal Article
Open access
PDF file
Md. Abu Ayub SiddiqueMd. Abu Ayub Siddique
Md. Abu Ayub Siddique
YKYong-Joo Kim
Yong-Joo Kim
Seung-Min BaekSeung-Min Baek
Seung-Min Baek
SBSeung-Yun Baek
Seung-Yun Baek
THTae-Ho Han
Tae-Ho Han
YCYong Choi
Yong Choi
This study focuses on the development of the reliability test method for the hydraulic pump of a tractor during major agricultural operations (plow, rotary, baler, and wrapping) at various driving and PTO (power take-off) gear stages. The hydraulic-pressure-measurement system was installed on the tractor. The measured hydraulic pressure and engine rotational speed were converted to the equivalent pressure and engine speed for each agricultural operation using a mathematical formula. Additionally, the overall equivalent pressure and overall engine speed were calculated to determine the acceleration lifetime. The average equivalent pressure and engine speed for plow tillage were calculated at around 5.44 MPa and 1548.37 rpm, respectively, whereas the average equivalent pressure and engine speed for rotary tillage were almost 5.70 MPa and 2074.73 rpm, accordingly. In the case of baler and wrapping operations, the average equivalent pressure and engine speed were approximately 11.22 MPa and 2203.01 rpm, and 11.86 MPa and 913.76 rpm, respectively. The overall hydraulic pressure of the pump and the engine rotational speed were found to be around 10.07 MPa and 1512.93 rpm, respectively. The acceleration factor was calculated using the overall pressure and engine speed accounting for 336. In summary, the developed reliability test method was evaluated by RS-B-0063, which is the existing reliability evaluation standard for agricultural hydraulic gear pumps. The evaluation results proved that the developed reliability test method for the hydraulic pump of a tractor satisfied the standard criteria. Therefore, it could be said that the developed reliability test method could be applicable to the hydraulic pump of the tractor during agricultural field operations.

29 October 2023 in Agriculture
Verified
Journal Article
Open access
PDF file
YMYi-Seo Min
Yi-Seo Min
Yeon-Soo KimYeon-Soo Kim
Yeon-Soo Kim
RLRyu-Gap Lim
Ryu-Gap Lim
WKWan-Soo Kim
Wan-Soo Kim
YKYong-Joo Kim
Yong-Joo Kim
Wan-Soo KimWan-Soo Kim
Wan-Soo Kim
The load factor (LF) of a tractor represents the ratio of actual engine power and rated engine power, and is an important indicator directly used in calculating national air pollutant emissions. Currently, in the Republic of Korea, a fixed value of 0.48 is used for the LF regardless of the working conditions, making it difficult to establish a reliable national air pollutant inventory. Since tractors perform work under soil conditions, soil physical properties directly affect the tractor LF. Therefore, it is expected that more accurate LF estimation will be possible by utilizing soil physical properties. This study was conducted to assess the impact of soil physical properties on the LF. Experimental data were collected in ten different soil conditions. Correlation analysis revealed that the LF exhibited strong correlations with SMC, soil texture, and CI, in that order. The coefficient of determination for the regression model developed using soil variables ranged from 0.678 to 0.926. The developed regression models generally showed higher accuracy when utilizing multiple soil variables, as compared to using a single soil variable. Therefore, an effective estimation of the LF through non-experimental methods can be achieved by measuring various soil properties.

23 December 2022 in Agriculture
Verified
Journal Article
Open access
PDF file
Md. Abu Ayub SiddiqueMd. Abu Ayub Siddique
Md. Abu Ayub Siddique
Seung-Min BaekSeung-Min Baek
Seung-Min Baek
SBSeung-Yun Baek
Seung-Yun Baek
YKYong-Joo Kim
Yong-Joo Kim
RLRyu-Gap Lim
Ryu-Gap Lim
The objectives of this study are the development and verification of a simulation model of the partial PST (power-shift transmission) tractor based on actual field operations. The PST simulation model was verified for the asphalt driving condition, and performance was evaluated for asphalt driving, plow, and rotary tillage. In this study, the traditional, APS (Auto Power Shift) ECO, and APS power engine modes were used to analyze fuel consumption. The statistical analysis proved that the experimental and simulation results were in a linear relationship, with an accuracy of over 98%. Finally, the results suggested that users could utilize the 95-kW partial PST tractor in the APS ECO engine mode with higher fuel economy compared to the traditional and APS power modes.

22 June 2023 in Machines
Verified
Journal Article
Open access
PDF file
YMYi-Seo Min
Yi-Seo Min
YKYong-Joo Kim
Yong-Joo Kim
RLRyu-Gap Lim
Ryu-Gap Lim
TSTaeyong Sim
Taeyong Sim
WKWan-Soo Kim
Wan-Soo Kim
Wan-Soo KimWan-Soo Kim
Wan-Soo Kim
The performance of the electrohydraulic proportional control valve (EHPV) employed in a tractor’s automatic steering system directly influences the steering performance. To develop a highly reliable EHPV, it is essential to analyze the hydraulic characteristics of the EHPV for several working conditions of tractors. This study aimed to measure and analyze the hydraulic characteristics of the EHPV according to tractor working conditions. The flow rate and pressure data of the EHPV were computed through the valve measuring system, and the required power was computed. The experimental conditions were selected based on engine rotational speed and tractor steering angle. As a result, it was discovered that the flow rate, pressure, and power all increased when the engine rotation speed and steering angle conditions increased. Furthermore, the rates of increase in flow rate, pressure, and power based on the increase in the steering angle were higher than when the engine rotation speed increased. In the regression analysis results between the two variables and the hydraulic characteristics of EHPVs, the steering angle demonstrated a higher correlation than the engine rotation speed. In conclusion, the steering angle and engine rotational speed are the major variables in the hydraulic characteristics of EHPVs, and the influence of the steering angle is greater.

15 October 2023 in Agriculture
Verified
Journal Article
Open access
PDF file
RLRyu-Gap Lim
Ryu-Gap Lim
Wan-Soo KimWan-Soo Kim
Wan-Soo Kim
YDYoung-Woo Do
Young-Woo Do
Md. Abu Ayub SiddiqueMd. Abu Ayub Siddique
Md. Abu Ayub Siddique
YKYong-Joo Kim
Yong-Joo Kim
In this study, a model of the frame-type ROPS (rollover protective structure) for an agricultural tractor was developed using FEA (finite-element analysis). Various boundary conditions were applied as input variables to replace the actual test of the ROPS with a virtual test. An optimization study was carried out based on the boundary conditions of the bolt, considering the ROPS part directly mounted on the tractor and the folding connection to the ROPS. The results of the virtual test were compared with those of the actual test, and the error was determined. The maximum error of the evaluation model was 7.0% for the force applied on the load and 9.6% for the corresponding ROPS deformation. All mounting bolts of the ROPS required modeling. In particular, we had to establish free boundary conditions for axial rotation to implement the folding connection. In addition, a simulation of the frame-type ROPS was conducted according to the mesh size. A convenient simulation time was obtained for a mesh size of 8~10 mm. Compared with the actual test, the accuracy was the highest with a mesh size of 6~8 mm.