The load factor (LF) of a tractor represents the ratio of actual engine power and rated engine power, and is an important indicator directly used in calculating national air pollutant emissions. Currently, in the Republic of Korea, a fixed value of 0.48 is used for the LF regardless of the working conditions, making it difficult to establish a reliable national air pollutant inventory. Since tractors perform work under soil conditions, soil physical properties directly affect the tractor LF. Therefore, it is expected that more accurate LF estimation will be possible by utilizing soil physical properties. This study was conducted to assess the impact of soil physical properties on the LF. Experimental data were collected in ten different soil conditions. Correlation analysis revealed that the LF exhibited strong correlations with SMC, soil texture, and CI, in that order. The coefficient of determination for the regression model developed using soil variables ranged from 0.678 to 0.926. The developed regression models generally showed higher accuracy when utilizing multiple soil variables, as compared to using a single soil variable. Therefore, an effective estimation of the LF through non-experimental methods can be achieved by measuring various soil properties.
The performance of the electrohydraulic proportional control valve (EHPV) employed in a tractor’s automatic steering system directly influences the steering performance. To develop a highly reliable EHPV, it is essential to analyze the hydraulic characteristics of the EHPV for several working conditions of tractors. This study aimed to measure and analyze the hydraulic characteristics of the EHPV according to tractor working conditions. The flow rate and pressure data of the EHPV were computed through the valve measuring system, and the required power was computed. The experimental conditions were selected based on engine rotational speed and tractor steering angle. As a result, it was discovered that the flow rate, pressure, and power all increased when the engine rotation speed and steering angle conditions increased. Furthermore, the rates of increase in flow rate, pressure, and power based on the increase in the steering angle were higher than when the engine rotation speed increased. In the regression analysis results between the two variables and the hydraulic characteristics of EHPVs, the steering angle demonstrated a higher correlation than the engine rotation speed. In conclusion, the steering angle and engine rotational speed are the major variables in the hydraulic characteristics of EHPVs, and the influence of the steering angle is greater.
Autonomous tractors are emerging as a pivotal technology in agricultural automation. Precise steering control in these tractors requires high-performance electrohydraulic proportional valves (EHPVs). To optimize EHPV performance and reduce development costs and time, simulation analysis serves as a valuable pre-testing tool. This study aimed to develop a simulation model capable of predicting the hydraulic characteristics of EHPVs under real-world operating conditions. The model was created using AMESim, incorporating actual tractor operating conditions and valve control signals. The proposed model was validated through experiments conducted on a tractor equipped with an EHPV, evaluating hydraulic characteristics across various engine speeds and steering angular velocities. The simulation model was utilized to analyze the priority valve control flow characteristics of the automatic steering system and the hydraulic response of the EHPV under step inputs at specific engine speed points. The results indicate that the simulation model demonstrated a mean absolute percentage error (MAPE) ranging from 7.45% to 9.79% for hydraulic power. A t-test analysis of hydraulic power indicated no statistically significant difference between the simulation and experimental values under all test conditions. The proposed EHPV simulation model can be utilized for the optimal future design of EHPV systems.
This study attempted to develop and validate a data-driven simulation model that integrates field-measured data to assess the power requirement and fuel consumption characteristics of a self-propelled collector. The collector is a hydrostatic transmission-based, crawler-type platform designed for garlic and onion harvesting, equipped with multiple hydraulic subsystems for collection and sorting. During field experiments, the power requirements of each subsystem and fuel flow rate were recorded, and Willans line method was applied to estimate engine power and subsystem power transmission efficiencies. Because many small agricultural machines do not support electronically instrumented engines (e.g., CAN-bus/ECU-based measurements), the proposed model was formulated as a data-driven, low-order representation derived from on-site measurements rather than a full physics-based model. Using the identified parameters, the simulation framework predicts engine power and fuel efficiency under various operating conditions. The simulation results exhibited high agreement with field data, achieving R2 and mean absolute percentage error values of 0.935–0.981 and 1.79–4.18%, respectively, confirming reliable reproduction of real field performance. A comprehensive analysis of the simulation results revealed that both engine speed and travel speed significantly influence power distribution and fuel rate, while also indicating that hydraulic working power is the dominant contributor to total power demand at higher engine speeds. These findings provide practical guidance for improving the fuel efficiency of compact self-propelled collectors.
Garlic is a labor-intensive underground crop in Republic of Korea, where harvesting and collection require substantial manual work. Although self-propelled garlic collectors have been introduced, most were developed empirically, and quantitative evaluations of their load characteristics and power requirements under field conditions remain limited. This study quantifies the power requirements of the driving, collection, and transport parts of a self-propelled garlic collector and examines the effects of driving speed, collecting speed, transporting speed, and working depth. A field measurement system was developed to record torque, rotational speed, flow rate, and pressure, and these data were used to calculate the power requirement of each major component and the overall machine. Results showed that driving speed was the dominant factor affecting total power use, as the driving part displayed a clear increase with higher speeds. In contrast, the collection and transport parts exhibited only minor changes, and the influence of working depth was negligible. The maximum total power requirement was 12.28 kW, about 30% of the rated engine power of 40.2 kW, indicating that engine capacity exceeded actual requirement. These findings provide quantitative insights into self-propelled garlic collectors and essential data for future studies on engine downsizing and power transmission design.
The stream of onions entering a self-propelled onion collector varies with field conditions, feeding density, and the transient lifting behavior of the onion–soil mass, whereas the collection conveyor is conventionally operated at a fixed speed, wasting hydraulic energy. This study proposes and evaluates, through field-calibrated simulation, a vision-based feedforward conveyor speed control framework that couples reel-synchronous onion counting with variable-displacement pump control. To mitigate the periodic occlusion caused by the compact dual-conveyor structure, a frame-selection method synchronized with the detected conveyor position was implemented, and a YOLOv8n detector was trained and evaluated on 314 images extracted from 32 indoor and field source videos partitioned at the source-video level. On the independent test subset, the model achieved precision, recall, and mAP@0.5 of 0.952, 0.944, and 0.959, and the proposed counting method maintained count recovery ratios above 95% across all engine speeds in 45 independent field trials, outperforming fixed-period sampling and tracking-based baselines by 6.6 and 3.8 percentage points, respectively. An AMESim model of the fixed-displacement hydraulic system was calibrated and shown to be consistent with field measurements and was then used to evaluate the variable-displacement configuration. Net conveyor-related fuel savings (engine no-load consumption subtracted) were estimated at 14.3–18.7% under the field-identified constant transmission efficiency, with conservative estimates of 11.5–16.9% when partial-displacement efficiency losses were accounted for through an anchored loss model. These results demonstrate the feasibility of vision-based feedforward conveyor speed control and its potential for energy savings in bulb-crop collection.