In the field of agricultural machinery, various empirical field tests are conducted to measure design loads for the optimal design and implementation of tractors. However, conducting field tests is costly and time-consuming, with many constraints on weather and field soil conditions, and research utilizing simulations has been proposed as an alternative to overcome these shortcomings. The objective of this study is to develop a DEM-based draft force prediction model that reflects differences in soil properties. For this, soil property measurements were conducted in two fields (Field A in Daejeon, Republic of Korea, and Field B in Chuncheon, Republic of Korea). The measured properties were used as parameters for DEM-based particle modeling. For the interparticle contact model, the EEPA contact model was used to reflect the compressibility and stickiness of cohesive soils. To generate an environment similar to real soil, particle mass and surface energy were calibrated based on bulk density and shear torque. The soil property measurements showed that Field B had a higher shear strength and lower cone index and moisture content compared to Field A. The actual measured draft force was 19.47% higher in Field B than in Field A. In this study, this demonstrates the uncertainty in predicting draft force by correlating only one soil property and suggests the need for a comprehensive consideration of soil properties. The simulation results of the tillage operation demonstrated the accuracy of the predicted shedding force compared to the actual field experiment and the existing theoretical calculation method (ASABE D497.4). Compared to the measured draft force in the actual field test, the predictions were 86.75% accurate in Field A and 74.51% accurate in Field B, which is 84% more accurate in Field A and 37.32% more accurate in Field B than the theoretical calculation method. This result shows that load prediction should reflect the soil properties of the working environment, and is expected to be used as an indicator of soil–tool interaction for digital twin modeling processes in the research field of bio-industrial machinery.
The objective of this study was to analyze the effect of tillage type (i.e., primary and secondary tillage) and gear selection (P1L2 to P1L4) on the working load of tractor–implement systems during rotary tillage. Soil properties change with depth, and differences in properties along the depth distribution, such as the location of formation of the hardpan layer, internal friction angle, and moisture content, affect the load of rotary tillage operations. Therefore, the physical properties of soil along the field depth distribution were measured to analyze the effect of tillage type and gear selection on workload in rotary tillage. In addition, a load measurement system equipped with PTO torque meter, axle torque meter, proximity sensor, and RTK-GPS were configured on the 42 kW agricultural tractor. The experimental results show that the combination of tillage type and gear selection has a wide-ranging effect on the tractor’s workload and performance when the rotavator operated at the same tilling depth. Overall working load was higher by up to 14% (engine) and 29.1% (PTO shaft) in primary tillage compared to secondary tillage when the gear selection was the same. When the tillage type is the same, it was analyzed that the overall average torque increased by up to 35.9% (engine) and 33.9% (PTO shaft) in P1L4 compared to P1L2 according to gear selection. Based on load analysis results, it was found that the effect of gear selection (Engine: 4–14%, PTO: 12.1–28.6%) on engine and PTO loads was higher than that of tillage type (Engine: 31.6–35.1%, PTO: 31.9–32.8%), and the power requirement tended to decrease in secondary tillage. Therefore, working load should be considered according to the soil environment and tillage type when designing agricultural machinery system.
The load factor (LF) of a tractor represents the ratio of actual engine power and rated engine power, and is an important indicator directly used in calculating national air pollutant emissions. Currently, in the Republic of Korea, a fixed value of 0.48 is used for the LF regardless of the working conditions, making it difficult to establish a reliable national air pollutant inventory. Since tractors perform work under soil conditions, soil physical properties directly affect the tractor LF. Therefore, it is expected that more accurate LF estimation will be possible by utilizing soil physical properties. This study was conducted to assess the impact of soil physical properties on the LF. Experimental data were collected in ten different soil conditions. Correlation analysis revealed that the LF exhibited strong correlations with SMC, soil texture, and CI, in that order. The coefficient of determination for the regression model developed using soil variables ranged from 0.678 to 0.926. The developed regression models generally showed higher accuracy when utilizing multiple soil variables, as compared to using a single soil variable. Therefore, an effective estimation of the LF through non-experimental methods can be achieved by measuring various soil properties.
The performance of the electrohydraulic proportional control valve (EHPV) employed in a tractor’s automatic steering system directly influences the steering performance. To develop a highly reliable EHPV, it is essential to analyze the hydraulic characteristics of the EHPV for several working conditions of tractors. This study aimed to measure and analyze the hydraulic characteristics of the EHPV according to tractor working conditions. The flow rate and pressure data of the EHPV were computed through the valve measuring system, and the required power was computed. The experimental conditions were selected based on engine rotational speed and tractor steering angle. As a result, it was discovered that the flow rate, pressure, and power all increased when the engine rotation speed and steering angle conditions increased. Furthermore, the rates of increase in flow rate, pressure, and power based on the increase in the steering angle were higher than when the engine rotation speed increased. In the regression analysis results between the two variables and the hydraulic characteristics of EHPVs, the steering angle demonstrated a higher correlation than the engine rotation speed. In conclusion, the steering angle and engine rotational speed are the major variables in the hydraulic characteristics of EHPVs, and the influence of the steering angle is greater.