The automatic emergency braking (AEB) system of the passenger car is responsible for auxiliary braking judgment and decision-making in an emergency. Due to the inevitable pressure response delay of passenger car pneumatic braking systems, a large number of verification tests should be carried out to propose appropriate strategies and algorithms. To realize the rapid verification of the AEB control algorithm, a verification system integrating software-in-the-loop (SIL) and hardware-in-the-loop (HIL) was proposed for a two-axle passenger car. It can verify the logic feasibility of the control algorithm through SIL testing, and can verify the implementation effect of the control algorithm through HIL testing. The verification system is composed of IPG, dSPACE, and a pneumatic braking bench. Considering the influence of pneumatic braking delay, it is well-matched with the actual vehicle AEB system. The AEB hierarchical control algorithm was verified under three typical test conditions. The results show that the SIL testing results of speed and relative distance are in good agreement with the HIL testing results, and the average relative deviation of relative distance is only 1.7 m. The single test time of the SIL testing is about 228 s, which can meet the requirements of rapid verification of the AEB control algorithm of the passenger car.
To ensure that a liquid tank semi-trailer has good yaw stability and path-following performance on low-adhesion roads under turning conditions, a multi-object PID differential braking-control method is proposed, which takes the tractor yaw rate, semi-trailer yaw rate, and articulation angle as the control parameters. According to the principle of equivalence, the trammel pendulum (TP) model is used to simulate the liquid sloshing effect in the liquid tank, and the Fluent software is used to identify the key parameters of the trammel pendulum model and verify the correctness of its simulation effect. Then, a co-simulation model is built based on TruckSim and MATLAB/Simulink. Based on the simplified six degrees of freedom model and the co-simulation model of a liquid tank semi-trailer, a multi-object PID differential braking-control method is designed, and the vehicle state responses with and without control are compared when it is turning on a low-adhesion road. The simulation results show that the proposed multi-object PID differential braking-control method can effectively improve the yaw stability and path-following performance of the liquid tank semi-trailer when turning on a low-adhesion road.
20 April 2022 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
The electronically controlled pneumatic brake system (ECPBS) of semitrailer transport vehicle for dangerous cargo (STVDC) is required to control the brake pressure in each brake chamber accurately and stably. Accordingly, the brake pressure change rate (BPCR) in the brake chamber is taken as one of the evaluation parameters and control indicators of ECPBS for STVDC in this paper; an online monitoring implementation scheme of the BPCR in the brake chamber is designed; a simplified model is built based on AMESim and verified by hardware-in-the-loop experiments based on dSPACE; finally, the online monitoring function of BPCR in the brake chamber is validated with the simplified model. This paper provides a new idea for the design and development of ECPBS for STVDC.
The semi-trailer ECPBS is adopted to achieve coordinated braking between tractor and trailer. Its control strategies are mainly verified through MIL and HIL tests. The correctness of the test results relies on the precision of the models. The dependence on the vehicle simulation models can be greatly reduced through an in-loop testing system, which combines the ECPB hardware test bench with the semi-trailer twin test vehicle. However, due to the long spatial distance between the two, higher requirements are placed on the real-time performance of the testing system. The communication interconnection mode, distributed network architecture, data coupling method and data coupling method of the in-loop testing system were investigated. Moreover, a delay compensation controller based on model prediction was designed and was applied to the motion control of the twin test vehicle. The simulation results have shown that the compensation controller can ensure the stability of vehicle motion with a goodness-of-fit of 0.826 under a delay of 0.7 s. Further experimental verification shows that the instructions issued by the ECPB hardware test bench controller can reach the semi-trailer twin test vehicle within 0.6 s, indicating that the communication interconnection method is feasible and can meet the real-time requirements of the in-loop testing system.
This paper presents an X-in-Loop test platform designed for the proof-of-concept testing of intelligent braking ECPBS in commercial vehicle. Firstly, the concept of intelligent braking is introduced, outlining its research scope and defining the necessary test requirements for the proof of concept. Based on these experimental criteria, the composition and operational principles of the proof-of-concept experimental platform are developed in accordance with X-in-Loop testing methodologies. The various subsystems and functionalities of the X-in-Loop proof-of-concept test platform are subsequently detailed. The working principle of the X-in-Loop proof-of-concept test platform is thoroughly explained using a loop example, and its workflow is presented. Finally, the platform’s fundamental functionalities are validated through a vehicle braking test conducted under specific working conditions, followed by an analysis of its potential applications.
In this paper, by analyzing the heat and mass transfer characteristics of the dehumidification runner microelement channel of a drinking water emergency extraction vehicle, a mathematical model of heat and mass transfer in the water intake process is established, and the influence of the runner parameters (adsorbent thickness, regeneration angle, rotation speed) and air parameters (treatment air temperature/humidity, regenerated air temperature/humidity) on the water intake characteristics is mainly studied. Water extraction experiments are carried out in arid desert areas and humid island environments. The test results showed that compared with the calculated data, the deviations in the temperature and humidity of the treated air outlet were 3.03% and 4.14%, respectively, and the deviation value of the water intake was 8.23% when the moisture content of the inlet air was 2 g/kg.