The crystallization kinetics and structure evolution during annealing of the Ni45.5Co4.5Mn36.6In13.4 (at. %) powders produced by mechanical alloying (MA) was investigated. After 70 h and 100 h of MA, the powder consisted of a mixture of amorphous and nanocrystalline body-centered cubic (bcc) phases. We observed the relaxation in the as-received powder. The relaxation temperature (Tre) increases logarithmically with the annealing time. Annealing above 440 °C results in (1) ordering of L21, (2) dissolution of the residual Ni and Mn, (3) tetragonal MnNi phase formation and (4) γ phases precipitation. The activation energies of the B2 → L21 and Mn (α-Mn) → MnNi (P4/mmm) transformations were calculated.
The effect of high-temperature heat treatment on the microstructure and mechanical properties of post-operation P91 steel (X10CrWMoVNb9-1) was investigated. The tensile test results confirmed the significant effects of heat treatment type and duration on the properties of P91 steel. The absence of tempering resulted in high strength, reduced ductility, and limited microstructural stability. The tensile strength after normalization was nearly twice as high (1330 MPa) than the UTS value of the as-received sample (692 MPa). The decrease in elongation (9.9%) was related to the presence of supersaturated martensite in the microstructure. Tempering at 780 °C for 4 h with air cooling decreased the strength to UTS = 642 MPa and simultaneously increased the ductility (EL = 11.2%) at a hardness of 240 HV0.1. These changes were associated with microstructural evolution, including the formation and dispersion of precipitates. The most uniform microstructure, characterized by a relatively even distribution of 0.30 µm precipitates and reduced martensitic morphology, was observed after double tempering for 2 h + 2 h at 780 °C with air cooling. High-temperature tempering significantly changed the fracture characteristics and fracture morphology, eliminating martensite brittleness while gradually restoring the ductile nature of the fracture. The results indicate that controlled tempering allows for the formation of a stable microstructure with balanced mechanical properties suitable for high-temperature operation.
In this work, small amounts of Fe or Cr were added to Ni47Co3Mn36.5In13.5 alloy (x = 0) to produce five-component alloys with nominal compositions of Ni47Co3Mn35.5In13.5Fe1, Ni47Co3Mn33.5In13.5Fe3, Ni47Co3Mn35.5In13.5Cr1, and Ni47Co3Mn33.5In13.5Cr3, which are denoted as Ni47Co3Mn36.5−xIn13.5Fex/Crx (x = 1, 3 at.% Cr/Fe) series or as Mn-series (due to the addition of alloying elements instead of Mn), and Ni47Co3Mn36.5In12.5Fe1, Ni47Co3Mn36.5In10.5Fe3, Ni47Co3Mn36.5In12.5Cr1, and Ni47Co3Mn36.5In10.5Cr3, denoted as Ni47Co3Mn36.5In13.5−x (x = 1, 3 at.% Cr/Fe) series or In-series (due to the addition of alloying elements instead of In). The polycrystalline alloys were produced using the vacuum arc melting technique. The as-received alloys were characterized in structure, homogeneity, phase composition, martensitic transformation, and microhardness. The results showed that the addition of 1 at.% of Cr or Fe positively impacted the microstructure of the alloys. The quaternary alloy exhibited a single-phase coarse-grained structure. The addition of Fe and Cr (1 at.%) caused microstructure refinement with small Fe/Cr- and Co-rich γ particles appropriately distributed in the matrix, while the addition of 3% Fe or Cr resulted in γ formation in a dendritic form distributed more randomly. The addition of 1 at.% and 3 at.% of Cr or Fe significantly influenced the martensitic transformation temperatures. The microhardness increased by 21% in the Ni47Co3Mn33.5In13.5Fe3 alloy compared to the quaternary alloy.