Karsten Manterys

Dr. Karsten Manterys

Institute of Materials Engineering, University of Silesia in Katowice
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 May 2023 in Polymer Testing
Verified
Journal Article
Open access
JLJan Loskot
Jan Loskot
DJDaniel Jezbera
Daniel Jezbera
RLRoman Loskot
Roman Loskot
DBDamián Bušovský
Damián Bušovský
Adrian BarylskiAdrian Barylski
Adrian Barylski
MZMaciej Zubko
Maciej Zubko

5 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
KMKarsten Manterys
Karsten Manterys
MZMaciej Zubko
Maciej Zubko
PŚPaweł Świec
Paweł Świec
Krystian PrusikKrystian Prusik
Krystian Prusik
MSMagdalena Szklarska
Magdalena Szklarska
DSDanuta Stróż
Danuta Stróż
The presented work was focused on investigating the influence of the (hafnium and zirconium)/molybdenum ratio on the microstructure and properties of Ti20Ta20Nb20(ZrHf)20−xMox (where: x = 0, 5, 10, 15, 20 at.%) high entropy alloys in an as-cast state. The designed chemical composition was chosen due to possible future biomedical applications. Materials were obtained from elemental powders by vacuum arc melting technique. Phase analysis revealed the presence of dual body-centered cubic phases. X-ray diffraction showed the decrease of lattice parameters of both phases with increasing molybdenum concentration up to 10% of molybdenum and further increase of lattice parameters. The presence of two-phase matrix microstructure and hafnium and zirconium precipitates was proved by scanning and transmission electron microscopy observation. Mechanical property measurements revealed decreased micro- and nanohardness and reduced Young’s modulus up to 10% of Mo content, and further increased up to 20% of molybdenum addition. Additionally, corrosion resistance measurements in Ringers’ solution confirmed the high biomedical ability of studied alloys due to the presence of stable oxide layers.

1 September 2019 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
EMEdyta Matyja
Edyta Matyja
Krystian PrusikKrystian Prusik
Krystian Prusik
MZMaciej Zubko
Maciej Zubko
Grzegorz DerczGrzegorz Dercz
Grzegorz Dercz
KMKarsten Manterys
Karsten Manterys

9 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
KMKarsten Manterys
Karsten Manterys
MZMaciej Zubko
Maciej Zubko
SGSandra Gębura
Sandra Gębura
PŚPaweł Świec
Paweł Świec
Krystian PrusikKrystian Prusik
Krystian Prusik
DSDanuta Stróż
Danuta Stróż
The presented work aimed to investigate the influence of the hafnium/(zirconium and molybdenum) ratio on the microstructure, microhardness and corrosion resistance of Ti20Ta20Nb20(ZrMo)20−xHfx (where x = 0, 5, 10, 15 and 20 at.%) high entropy alloys in an as-cast state produced from elemental powder and obtained via the vacuum arc melting technique. All studied alloys contained only biocompatible elements and were chosen based on the thermodynamical calculations of phase formation predictions after solidification. Thermodynamical calculations predicted the presence of multi-phase, body-centered cubic phases, which were confirmed using X-ray diffraction and scanning electron microscopy. Segregation of alloying elements was recorded using elemental distribution maps. A decrease in microhardness with an increase in hafnium content in the studied alloys was revealed (512–482 HV1). The electrochemical measurements showed that the studied alloys exhibited a high corrosion resistance in a simulated body fluid environment (breakdown potential 4.60–5.50 V vs. SCE).

30 October 2020 in Metals
Verified
Journal Article
Open access
PDF file
KMKarsten Manterys
Karsten Manterys
MZMaciej Zubko
Maciej Zubko
PŚPaweł Świec
Paweł Świec
Krystian PrusikKrystian Prusik
Krystian Prusik
RARobert Albrecht
Robert Albrecht
DSDanuta Stróż
Danuta Stróż
Presented work was focused on obtaining new, up to our knowledge, non-described previously in the literature high entropy Co15Cr15Mo25Si15Y15Zr15 alloy to fill in the knowledge gap about the six-elemental alloys located in the adjacent to the center of phase diagrams. Material was obtained using vacuum arc melting. Phase analysis revealed the presence of a multi-phase structure. Scanning electron microscopy microstructure analysis revealed the existence of three different phases with partially dendritic structures. Chemical analysis showed that all phases consist of all six principal elements—however, with different proportions. Transmission electron microscopy microstructure analysis confirmed the presence of amorphous and nanocrystalline areas, as well as their mixture. For the studied alloy, any phase transformation and solid-state crystallization were not revealed in the temperature range from room temperature up to 1350 °C. Nanoindentation measurements revealed high nanohardness (13(2) GPa and 18(1) GPa for dendritic and interdendritic regions, respectively) and relatively low Young’s modulus (185(23) GPa and 194(9) GPa for dendritic and interdendritic regions, respectively) of the observed phases.

4 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
KMKarsten Manterys
Karsten Manterys
MZMaciej Zubko
Maciej Zubko
PŚPaweł Świec
Paweł Świec
Krystian PrusikKrystian Prusik
Krystian Prusik
MSMagdalena Szklarska
Magdalena Szklarska
DSDanuta Stróż
Danuta Stróż
The presented work considers the influence of the hafnium and molybdenum to zirconium ratio of Ti20Ta20Nb20(HfMo)20−xZrx (where x = 0, 5, 10, 15, 20 at.%) high-entropy alloys in an as-cast state for potential biomedical applications. The current research continues with our previous results of hafnium’s and molybdenum’s influence on a similar chemical composition. In the presented study, the microstructure, selected mechanical properties, and corrosion resistance were investigated. The phase formation thermodynamical calculations were also applied to predict solid solution formation after solidification. The calculations predicted the presence of multi-phase, body-centred cubic phases, confirmed using X-ray diffraction and scanning electron microscopy. The chemical composition analysis showed the segregation of alloying elements. Microhardness measurements revealed a decrease in microhardness with increased zirconium content in the studied alloys. The corrosion resistance was determined in Ringer’s solution to be higher than that of commercially applied biomaterials. The comparison of the obtained results with previously reported data is also presented and discussed in the presented study.