An intermediate fluid vaporizer (IFV) is a typical vaporizer of liquefied natural gas (LNG), which is used in a large number of LNG terminals. Since it requires a large supply of seawater during its operation, it generates a lot of energy consumption. In this study, to reduce the seawater consumption in the regasification system, the heat transfer process was first numerically calculated, and the heat transfer coefficient of the IFV was determined for different seawater inlet temperatures, seawater flow rates, and LNG flow rates. The calculation results of the heat transfer coefficient were integrated into the numerical model in HYSYS, and the minimum seawater flow of the IFV under different working conditions was obtained. For receiving terminals using multiple IFVs, this study programmed calculations based on optimization software. The operating configuration of the IFVs under different operating conditions was optimized to reduce the consumption of seawater in the regasification system of the LNG terminals.
Under the guidance of China’s goal of achieving carbon neutrality by 2060, the petrochemical industry is increasingly adopting energy-saving and emission-reduction technologies. To realize the low carbon operation of the LNG (liquefied natural gas) receiving terminal, an innovative SCV (submerged combustion vaporizer) flue gas carbon capture system using LNG cold energy was established, and the system also combined with an ORC (organic Rankine cycle). HYSYS software was used to simulate the process of the SCV flue gas carbon capture system and the LNG regasification system. The simulation results showed that the proposed system has low carbon emission and low energy consumption performance. Moreover, the sensitivity analysis of the evaporation pressure of working fluids, CO2 capture pressure, and CO2 capture temperature was carried out. The key parameters were optimized by HYSYS software to achieve the optimal operation cost of the system. When the evaporation pressure of working fluids, CO2 capture pressure, and CO2 capture temperature were set as 1300 kPa, 750 kPa, and 143.15 K, respectively, the optimized system resulted in an exergy efficiency of 13.63%, an LNG cold exergy utilization rate of 77.49%, a CO2 capture rate of 94.9%, and a CO2 capture capacity of 6620.4 kg/h.
This paper focuses on improving the operating efficiency of the Liquified Natural Gas (LNG) submerged pump system in the LNG receiving terminals and achieve energy saving. The minimum input energy consumption of the LNG submerged pump system is taken as the objective function, and an optimization model for the operation of the LNG submerged pump system with variable frequency speed is established. LINGO18.0 optimization software is used to solve the model to get the optimal LNG submerged pump operation plan that satisfies the constraints. Taking a certain LNG receiving terminal as an example, the operation optimization of its LNG submerged pump system is carried out, and the input energy consumption of the system before and after optimization is compared. The results show that the use of variable frequency pumps can reduce the energy consumption of the LNG submerged pump system of LNG receiving terminals, and the optimization model can reduce the input power consumption of the system by about 10% under different transportation conditions. After applying the optimization model to actual production, it is found that the model has certain practicability for guiding the production of LNG receiving terminal.
The coupled formation of wax crystals and hydrates is a critical issue for the safety of deep-sea oil and gas exploration and subsea transport pipeline flow. Therefore, this paper conducts an experimental study on the characteristics of methane hydrate formation in a water-in-oil (W/O) system with different wax crystal contents and explores the influence of different initial experimental pressures on the induction period and maximum rate of hydrate formation. The wavelet function was introduced to process the reaction rate and calculate the maximum speed of hydrate formation. Notably, the higher the pressure, the smaller the maximum rate of hydrate formation. We observed that wax crystal precipitation increases the viscosity of the emulsion, which limits the diffusion of gas in the liquid phase during hydrate nucleation and thus delays the hydrate nucleation. The methane gas precipitation also affects the remaining fraction’s wax content and therefore affects the wax precipitation. Secondary hydrate formation was observed several times during the experiment, increasing the risk of pipeline blockage. Overall, this work provides insights into the effect of wax crystal precipitation on hydrate behaviour that could facilitate flow assurance applications in subsea multiphase pipelines and inform the safe transportation of oil and gas pipelines.
Hydrogen energy is a crucial carrier for the growth of the energy system and its low-carbon transformation. Using natural gas as a carrier of hydrogen transport and the natural gas pipeline network for transportation is a significant step toward realizing large-scale and long-distance hydrogen transport. Hydrogen-mixed natural gas is mainly separated into hydrogen and natural gas by physical methods at present. High purity of hydrogen recovery, but the recovery rate is low. At the same time, compared with natural gas, liquefied natural gas is more economical and flexible. This study analyzes three typical cryogenic separation processes. The results show that the hydrogen separation efficiency and specific energy consumption increase and the liquefaction rate and energy consumption decrease as the hydrogen ratio increases. The energy consumption and specific energy consumption of C3-MRC are lower than the MRC and the cascade liquefaction processes. Besides, as the pressure increases in the C3-MRC liquefaction process, the liquefaction and hydrogen separation efficiency increase and subsequently drop. Different hydrogen content has the highest hydrogen separation efficiency and liquefaction efficiency under different feed gas pressure conditions. The total exergy losses of the C3-MRC are the least in different hydrogen fractions, which are 37.59% and 21.77% less in the 25% hydrogen fraction, and 37.89% and 21.37% less in the 30% hydrogen fraction. Moreover, the exergy efficiency of C3-MRC are 87.68% and 88.06% when the hydrogen fraction are 25% and 30%, higher than the other two processes, which implies that in 25% and 30% fractions, making it more suitable for separate the hydrogen by the cryogenic separation.