Aiming at the problems of large elastic deformation and low machining accuracy in cutting titanium alloy thin-walled parts, this paper establishes the finite element model of milling titanium alloy thin-walled parts, and simulates and analyses the milling process of titanium alloy thin-walled parts by the statics analysis module of ANSYS 15.0 software. The maximum deformation point of the workpiece in the milling process is determined. Then the combination of cutting parameters that can minimize the deformation is determined by the orthogonal experiments of four factors and four levels. This paper designs the single factor experiments, which study the distribution of the milling force and the deformation law of the parts in the milling process. Moreover, this paper carries out the optimal design of the cutting parameters by orthogonal experiments, which provides a reference for the selection of the cutting parameters for the bending thin-walled parts of titanium alloy.

Mechanical surface treatments are needed to perform on components for fatigue life enhancement by introducing beneficial compressive residual stress and material strengthening. In this study, the combined turning with low plasticity burnishing (LPB) surface modification process was performed for the sake of improving mechanical properties of Inconel 718. Firstly, the evolution of microstructure and residual stress after the LPB process were analyzed with the aid of electron backscatter diffraction (EBSD) and X-ray diffraction (XRD), respectively. Secondly, the tensile behavior of treated samples was investigated through tension tests. Finally, the micro-strengthening mechanism of Inconel 718, induced by the LPB process, was revealed. The results show that the peak compressive stress is increased by a factor of 4.2 after the LPB process. The grain refinement induced by the LPB process is attributed to the increase of average misorientation and the formation of high angle grain boundaries (HAGBs). The enhanced yield strength depends on the decreased average spacing and the increased HAGBs.

High cutting temperatures increase tool wear and reduce tool life. To achieve a longer tool life, coated carbide tools have been developed. In this study, the influence of tool coatings on the cutting temperature distribution during the orthogonal cutting of H13-hardened steel is investigated. Firstly, four coating materials, including TiC, TiN, Al₂O₃, and TiAlN, with the same coating thickness, are selected to evaluate the effects of coating materials on cutting temperature with finite element simulation. The maximum temperatures at the tool rake face and the temperatures at the coating–substrate interface are evaluated. It was found that the maximum temperatures at the tool rake face were the lowest and the highest when TiN and Al₂O₃ coating materials were applied, respectively. The TiAlN coating material had the best thermal barrier property. Then, the temperature distribution along the direction perpendicular to the tool rake face is investigated for TiAlN-coated tools with different coating thicknesses ranging from 3 μm to 10 μm. It is shown that the temperature gradient increases with the coating thickness. The coating thickness should be kept below 5 μm. Finally, cutting experiments validate the availability of the finite element model.

Three-dimensional printing technology has a precise manufacturing process that can control tiny pores and can design individualized prostheses based on the patient’s own conditions. Different porous structures were designed by controlling different parameters such as porosity, using UG NX to establish models with different porosities and using ANSYS to simulate stress and strain. Unidirectional compression and stretching simulations were carried out to obtain stress, strain, and deformation. Based on these data, a porosity was found to approximate the elastic modulus of the humeral bone scaffold. As the porosity increased, the equivalent elastic modulus decreased significantly in the lateral direction, and the maximum stress formed by the porous structure and deformation increased significantly. Four different finite element models and geometric models of cubic, face-centered cubic, honeycomb, and body-centered cubic unit structures were selected. Then these porous structures were simulated for tensile and compression experiments, and the simulation results were analyzed. The forming simulation of the finite element model was carried out, and the evolution of mechanical properties of the porous structure during the 3D printing process was analyzed. The results showed that designing the humeral bone scaffold as a porous structure could reduce the stiffness of the prosthesis, alleviate stress shielding around the prosthesis after surgery, enhance its stability, and prolong its service life. The study provides reference values and scientific guidance for the feasibility of porous humeral bone scaffolds and provides a basis for the research and design of clinical humeral bone scaffolds.

Femtosecond laser processing technology offers a promising technique for the preparation of micro and nanostructures of single-crystal silicon carbide (SiC), thanks to its high precision and non-destructive processing. However, further research is needed to optimize processing parameters, as well as improve efficiency and quality of the process. This study conducts experiments to explore the effects of femtosecond laser ablation on single-crystal SiC. The influence and significance of parameters, such as fluence (F), repetition rate, scan speed (S), multipass scanning (c) and numerical aperture on the performance of grooves, including groove depth, groove width, heat-affected zone (HAZ) width, material removal rate (MRR) and side wall inclination angle, were studied. The results show that the influence of fluence and numerical aperture on groove depth, groove width, HAZ width, MRR and side wall inclination angle is very significant. The scan speed has a very significant effect on the groove depth, groove width, HAZ width and side wall inclination angle but has insignificant effect on the MRR. Repetition rate and multipass scanning have a very significant effect on groove depth, HAZ width, MRR and side wall inclination angle and a moderately significant effect on groove width. The experimental methods of increasing the aspect ratio and reducing the HAZ width were studied, and a significance analysis was carried out. Fluence, multipass scanning and z-layer feed have significant effects on groove depth, groove width, aspect ratio, HAZ width and MRR. The influence of polarization angle on groove depth, groove width, aspect ratio and MRR is insignificant.