This paper presents the performance assessment and working fluid selection for a novel integrated vapor compression cycle-organic Rankine cycle system (i-VCC-ORC), which recovers ultra-low-temperature waste heat rejected (50 °C) by the condenser of a vapor compression cycle (VCC). The analyses are carried out for a vapor compression cycle of a refrigeration capacity (heat input) of 35kW along with the component sizing of the organic Rankine cycle (ORC). The effects of the operational parameters on integrated system performance were investigated. The integrated system performance is estimated in terms of net COP, cycle thermal efficiency and exergy efficiency by completely utilizing and recovering the heat rejected by the condenser of the VCC system. R600a-R141b with COP_net (3.54) and ORC thermal efficiency (3.05%) is found to be the most suitable VCC-ORC working fluid pair. The integration of the vapor compression refrigeration cycle with the organic Rankine cycle increases the COP of the system by 12.5% as compared to the standalone COP of the vapor compression system. Moreover, the sensitivity analysis results show that there exists an optimum operating condition that maximizes the thermal performance of the integrated system.

Climate change is changing global weather patterns, with an increase in droughts expected to impact crop yields due to water scarcity. Crops can be provided with water via underground pumping systems to mitigate water shortages. However, the energy required to pump water tends to be expensive and hazardous to the environment. This paper explores different sites in Sudan to assess the crop water requirements as the first stage of developing renewable energy sources based on water pumping systems. The crop water requirements are calculated for different crops using the CROPWAT and CLIMWAT simulation tools from the Food and Agriculture Organization (FAO) of the United Nations. Further, the crop water requirements are translated into electrical energy requirements. Accurate calculations of the energy needed will help in developing cost-effective energy systems that can help in improving yields and reducing carbon emissions. The results suggest that the northern regions tend to have higher energy demands and that the potential for renewable energy should be explored in these regions, which are more susceptible to drought and where crops tend to be under higher stress due to adverse climate conditions.

To extend drain intervals and improve efficiency, new engine oils with increased dispersant concentration and reduced viscosity are required. Low viscosity engine oils can increase the prevalence of boundary friction at low temperature and increase its severity at higher temperatures. As a result, combinations of organic and inorganic friction modifiers (FM) will be used to reduce boundary friction across a range of temperatures, also preventing damage to vehicle catalysts. This paper presents an experimental case study of such a new generation of fully formulated engine lubricants with varying concentrations of polyisobutylene succinimide dispersant, organic, and inorganic FM. Representative conditions pertaining to those encountered at the top dead center reversal of the piston compression ring-cylinder liner contact are created, and the generated friction measured through use of a sliding-strip tribometry. Subsequently, X-ray photoelectron spectroscopy (XPS) is used to determine the composition of the formed surface tribofilms in order to explain the observed frictional characteristics. The key interactions and frictional behavior of the dispersant and friction modifiers are highlighted across a range of operating temperatures.

Heat loss through the building envelope comprises air leaks through the cracks and largely through the windows, which is the weakest link of the thermal envelope. Therefore, it is necessary to devise a systematic approach to analyze the rightful selection of glass for buildings. The investigation is to analyze the energy-saving potential of different glasses and their comparisons to the initial capital cost to find the payback time in terms of energy saving by using two different types of equipment. The quantitative simulation study was completed on the Hourly Analysis Program (HAP) to analyze the annual energy consumption of the HVAC system for seven glasses and two types of chilled water equipment. The results show that the performance glasses with a tint had better efficiency in terms of energy saving, with a payback time of 3–7 months. A comparison of all glasses illustrated that float glass contributes the most to the total cooling load among all glasses, which were 5.04%, 5.7%, 7.6%, and 8.9% for the N, S, E, and W orientations, respectively. Moreover, the lowest contribution of glass to the total cooling load was given by tinted double-glazed glass, which was 2%, 2.3%, 3.0%, and 3.01% for N, S, E, and W orientations, respectively.