As a key component to ensure the safety and stability of the surface-mounted permanent magnet motor rotor, stress research on the sleeve has long been a subject that has attracted researchers. Fiber-reinforced composite materials have the characteristics of high specific strength, high specific modulus, and low eddy current loss. The use of a fiber-reinforced composite material sleeve that can effectively reduce the thickness of the sleeve and structural weight, and can improve the power density of the motor is an inevitable trend of the development of high-performance permanent magnet motors. This paper summarizes the matching of fibers and resins of composite materials to the sleeve: the stress design criteria, stress calculation method, and stress influencing factors of the composite sleeve; two typical stress-forming methods of the composite sleeve; and the preloading effect of the sleeve, strength, and rotor prototype performance testing. This paper focuses on the application of tension winding technology in sleeve forming. Based on the characteristics of composite material layer synthesis, this method has the advantages of high forming efficiency, small forming damage, easy realization of stress design, and a high preloading effect. This method can meet the sleeve-forming requirements of high-performance, large-scale, high-speed permanent magnet motors. However, the application of the new high-performance material system in the existing research is insufficient, the research on the technological factors in the tension winding process is scarce, and the performance testing method after the sleeve preparation is single, which needs further research.
The residual stress plays an important role in composite flywheel rotors composed of filament windings. The fiber tension during high-prestressed winding is the main source of the rotor deformation and residual stress of composite layers. In this study, the effect of the winding tension gradient on deformation was monitored in real-time. Two types of in-plane winding tension fluctuation methods were developed to investigate the effect of tension on deformation. Online and offline measurements were performed for the strain acquisition. A wireless strain instrument was used for online deformation monitoring and a laser scanner was used for the offline surface reconstruction. Additionally, different filament winding strategies were carried out to improve the efficiency of the winding tension by finite element analysis. The results indicated that the deviation between numerical and experimental results was within 8%. Based on the proposed numerical method, the influence of the in-plane and out-of-plane winding tension gradient distributions on the rotation process of the H-shaped rotor was analyzed. An in-plane winding strategy with variable tension was developed, which increased the initial failure speed by 160%.
The curvature feature makes the irradiance and absorptivity change, resulting in an uneven power density distribution, which affects the quality of composite parts. In this study, a theoretical model-based Super-Gaussian profile beam in the laser irradiation area was established to obtain the heat flux distribution on the curved surface. The effect of curvature on the surface scattering reflection, temperature distribution, and surface morphology were investigated and verified the validity of the theoretical model. Furthermore, the influence of the laser intensity distribution, laser inclination and curvature radius on the power density distribution and distribution uniformity were studied. Research indicated that the power density increases as the distance from the origin increase resulting from the variation of the irradiance and absorptance along the circumference. The flatter the intensity distribution of the laser beam in the height direction, the less uniform the power density distribution. Accordingly, the typical Gaussian profile beam significantly ameliorates the power density distribution. This research provides a novel understanding of using heat sources during laser heating thermoplastic tape placement.
23 November 2023 in Journal of Thermoplastic Composite Materials
The carbon fiber reinforced polyetheretherketone (CF/PEEK) composite material can achieve high efficiency and integrated assembly molding through in-situ consolidation, suitable for the preparation of high-speed motor rotor sleeves. However, the high forming temperature of CF/PEEK may cause demagnetization of the magnet once the temperature exceeds the curie temperature of the magnet. To address the insulation issues during the sleeve forming process, this study proposes using metal-containing multilayer thermal insulations (MTI) to prepare the insulation layer, which takes advantage of the heat transfer within the metal layer to achieve thickness-wise insulation. A finite element heat field model is established to analyze the effect of material thermal properties, layer structure, and thermal field conditions on the thermal insulation effect. The response surface methodology analysis shows that metal materials with high thermal conductivity and high volume-specific heat have better insulation performance. The highest temperature of the bottom surface of the copper-containing MTI is only 64% of that of the glass fiber reinforced polypropylene (GF/PP) layer MTI. Analysis of the layer structure shows that the closer the metal layer is to the heat source, the better the insulation effect. The sensitivity analysis of the thermal field conditions shows that the thermal conductivity of the inner layer has a greater impact on the insulation effect. Subsequently, the MTI containing copper was optimized in response to the specific insulation requirements of the motor rotor sleeve, providing a reference for the application of in-situ consolidated integrated assembly molding in thermoplastic composites.
19 January 2024 in Journal of Reinforced Plastics and Composites
GF/PP thermoplastic composite components predominantly employ metallic fasteners, leading to corrosion and weight issues. This study utilized an extrusion process to fabricate GF/PP thermoplastic composite rivets with properties akin to laminated panel materials. Through the controlled application of heat and pressure to the rivet ends, a novel connection structure was established. The article fabricated thermoplastic composite joints with varying end configurations and compared them with metallic rivet joints. Emphasizing the convex form, diverse multi-rivet links were crafted for single-lap tensile samples. Integrating tensile tests and strain gauge measurements, this research explored load distribution patterns across diverse rivet quantities and assessed the impact of size on distribution. Furthermore, finite element software was used to dissect the load distribution patterns and failure mechanisms in the multi-riveted connection structure. Drawing from experimental findings, convex GF/PP rivets exhibited an 18% higher tensile load than metallic ones, with a simultaneous 32% weight reduction. In multi-rivet connections, end rivets demonstrated higher load-bearing capacity. Enhanced spacing and plate width improved load distribution, elevating joint load capacity by 7% (spacing 25 mm to 55 mm) and 6% (width 30 mm to 55 mm). The simulation results indicate that increasing the spacing reduces the stress concentration at the first nail location.
26 April 2022 in Journal of Thermoplastic Composite Materials
A lap shear test is employed to evaluate the interfacial bonding strength between unidirectional CF/PEEK tapes as quantification of bonding quality. In this study, a novel tab is proposed to ameliorate bonding testing. The crucial role of developed tabs is to avoid the adherend fracture that is typically observed in specimens with conventional tabs. Specimens with different tab, bonding processes, and lap lengths are prepared and tested. Moreover, theoretical analysis is conducted to predict bonding strength, and finite element simulations are also performed for stress distribution in these specimens with different types of tabs. The experimental and theoretical results demonstrate that the full tab is employed in the bonding test, the stress concentration reduces nearly by 6 times, and the failure mode coincides with the expected requirement. Additionally, the highest estimation of bonding strength increases nearly by 69%, and is approximately consistent with the theoretical calculation, up to 98.6%. This tab configuration, with low dependence on processes and joint parameters, describes a straightforward and efficient procedure to meliorate the quantification of the bonding strength, and is found to be applicable in the tape placement process and single-lap-joint assemblies for thermoplastic composites.