To obtain the autoclave-level mechanical properties using in situ consolidation of thermoplastic composites by automated fiber placement (AFP) with high efficiency is the focus of recent research. Different heat resources were utilized to pursue improved mechanical properties and deposition rates but yet not very satisfactory. In this article, E-glass fiber/polypropylene laminates, manufactured by ultrasonic vibration–assisted AFP (UAFP) and autoclave, were compared by means of mechanical properties and crystallization. The interfacial bonding mechanism was analyzed theoretically based on the principle of ultrasonic heating and the autohesion. The orthogonal tests were designed to study the effect of the process parameters on the interlaminar shear strength (ILSS), including the ultrasonic amplitude, layup speed, and pressure, to optimize the manufacturing process of specimens. The mechanical tests and differential scanning calorimetry (DSC) were utilized to evaluate the ILSS, mode I interlaminar fracture toughness GIC, impact toughness, and degree of crystalline of laminates from hot-press and UAFP. The experimental results indicate that the ILSS of the specimens from UAFP can match with the hot-press specimens. The GIC and the impact toughness of the UAFP specimens are 59.9% and 20.1% lower than the hot-press ones, respectively, which are due to the lower degree of crystalline caused by the higher cooling rate during the UAFP process. The results of DSC show that the crystallinity of specimens made from UAFP is only 38.5%, whereas the 49.2% crystallinity is tested for the hot-press.
As a key component to ensure the safety and stability of the surface-mounted permanent magnet motor rotor, stress research on the sleeve has long been a subject that has attracted researchers. Fiber-reinforced composite materials have the characteristics of high specific strength, high specific modulus, and low eddy current loss. The use of a fiber-reinforced composite material sleeve that can effectively reduce the thickness of the sleeve and structural weight, and can improve the power density of the motor is an inevitable trend of the development of high-performance permanent magnet motors. This paper summarizes the matching of fibers and resins of composite materials to the sleeve: the stress design criteria, stress calculation method, and stress influencing factors of the composite sleeve; two typical stress-forming methods of the composite sleeve; and the preloading effect of the sleeve, strength, and rotor prototype performance testing. This paper focuses on the application of tension winding technology in sleeve forming. Based on the characteristics of composite material layer synthesis, this method has the advantages of high forming efficiency, small forming damage, easy realization of stress design, and a high preloading effect. This method can meet the sleeve-forming requirements of high-performance, large-scale, high-speed permanent magnet motors. However, the application of the new high-performance material system in the existing research is insufficient, the research on the technological factors in the tension winding process is scarce, and the performance testing method after the sleeve preparation is single, which needs further research.
The residual stress plays an important role in composite flywheel rotors composed of filament windings. The fiber tension during high-prestressed winding is the main source of the rotor deformation and residual stress of composite layers. In this study, the effect of the winding tension gradient on deformation was monitored in real-time. Two types of in-plane winding tension fluctuation methods were developed to investigate the effect of tension on deformation. Online and offline measurements were performed for the strain acquisition. A wireless strain instrument was used for online deformation monitoring and a laser scanner was used for the offline surface reconstruction. Additionally, different filament winding strategies were carried out to improve the efficiency of the winding tension by finite element analysis. The results indicated that the deviation between numerical and experimental results was within 8%. Based on the proposed numerical method, the influence of the in-plane and out-of-plane winding tension gradient distributions on the rotation process of the H-shaped rotor was analyzed. An in-plane winding strategy with variable tension was developed, which increased the initial failure speed by 160%.
17 April 2014 in Journal of Reinforced Plastics and Composites
Microwave curing of epoxy/glass fiber composites was investigated in this paper. By studying the reaction characteristics of the resin matrix, detailed curing processes were established. With the use of a self-designed pressure-exerting device, the resin weight fraction of the composites was controllable. The glass transition temperature was measured by differential scanning calorimetry, and the mechanical properties were determined by three-point-bend and uniaxial tensile tests at room temperature. The tensile failure surfaces of both microwave and thermally cured composites were observed with scanning electron microscope. A comparison of the microwave and thermal processes was conducted to evaluate the advantage of microwave curing process. The microwave process (a) and thermal process (b) were regarded as the optimized process for each curing method. It was concluded that the epoxy/glass composites cured by microwave radiation had slightly higher Tg, comparable flexural strength and better tensile properties. Furthermore, the microwave process had a great advantage in saving the cycle time.
11 January 2018 in Journal of Reinforced Plastics and Composites
In this study, the effect of a roller’s deformability on the placeability restricted by an incomplete contact between a laying roller and mould in an automated fiber placement process was analyzed. The incomplete contact phenomenon was defined theoretically through the differential geometry, and corresponding criteria of placeability were proposed by analyzing the mechanism of interlayer bonding. A finite element model was established to simulate the pressure distribution on the contact zone. The pressure measurement of laying on a curved mould was conducted and the infrared thermographic method was utilized to detect the layup defects. The results of the theoretical analysis showed that the criteria of placeability must satisfy complete contact and pressure’s uniformity simultaneously and be implemented in the condition of laying on a cylinder mould with a fixed angle trajectory. The deformability of the roller with different layup forces relates to its material module and its geometry. The finite element model of pressure distribution was verified by an experiment, and the quantitative relationship between the uniformity of pressure and roller’s module, mould’s radius and tows’ width was acquired by this model. With the increase of module and tows’ width, the uniformity decreases; while with the increase of mould’s radius, the uniformity increases. The thermographic results showed that optimized parameters can guarantee the interlaminar bonding to avoid delamination for laying on the curved mould with a restriction of the incomplete contact.