Hyunwoo Son

Prof. Hyunwoo Son

Electronic Engineering, Gyeongsang National University, Jinju, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2017
Verified
Conference Paper
Closed access
YJYoungwoo Ji
Youngwoo Ji
CJCheonhoo Jeon
Cheonhoo Jeon
HSHyunwoo Son
Hyunwoo Son
BKByungsub Kim
Byungsub Kim
HPHong-June Park
Hong-June Park
JSJae-Yoon Sim
Jae-Yoon Sim
Ultra-low-power (ULP) sensor technologies for the future internet of things have presented challenges in ULP implementation of reference circuits while keeping traditional requirements of stable performance. For voltage reference circuits, as an essential block in SoCs to generate various internal supply voltages, the bandgap voltage-reference (BGVR) scheme has been widely used since it provides a well-defined value with strong immunity to process/voltage/temperature variations. Nanowatt-consuming BGVR circuits have been recently proposed using a capacitor network and a leakage-based proportional-to-absolute-temperature (PTAT) circuit. On the other hand, the current reference circuit that is required to set internal bias current still presents difficulties in achieving both stable performance and ULP consumption. The general approach to building a current reference is to use a BGVR with additional resistors for V-to-I conversion. Though it can provide a well-defined stable current reference, it also requires excessively large resistance for ULP consumption. Another approach is a CMOS-based current reference circuit that tries to make the exponential term in the subthreshold current equation constant or temperature-independent, hence reducing process and temperature dependencies. While CMOS reference circuits have achieved ULP implementations, the current is still determined by a number of process and design parameters, resulting in large sensitivity to process variations. This paper presents a sub-10nW bandgap-reference (BGR) circuit that implements both voltage and current references in one circuit. The BGR circuit is implemented with a 0.18μm CMOS process and generates voltage and a current references of 1.238V and 6.64nA while consuming 9.3nW. The voltage and current references show standard deviations of 0.43% and 1.19% with temperature coefficients of 26ppm/°C and 283ppm/°C, respectively.

19 May 2017 in IEEE Transactions on Biomedical Circuits and Systems
Verified
Journal Article
Closed access
HSHyunwoo Son
Hyunwoo Son
HCHwasuk Cho
Hwasuk Cho
JKJahyun Koo
Jahyun Koo
YJYoungwoo Ji
Youngwoo Ji
BKByungsub Kim
Byungsub Kim
JSJae-Yoon Sim
Jae-Yoon Sim
This paper presents an amplifier-less and digitalintensive current-to-digital converter for ion-sensitive FET sensors. Capacitance on the input node is utilized as a residue accumulator, and a clocked comparator is followed for quantization. Without any continuous-time feedback circuit, the converter performs a first-order noise shaping of the quantization error. In order to minimize static power consumption, the proposed circuit employs a single-ended current-steering digital-to-analog converter which flows only the same current as the input. By adopting a switching noise averaging algorithm, our dynamic element matching not only mitigates mismatch of current sources in the current-steering DAC, but also makes the effect of dynamic switching noise become an input-independent constant. The implemented circuit in 0.35 μm CMOS converts the current input with a range of 2.8 μA to 15 b digital output in about 4 ms, showing a DNL of +0.24/-0.25 LSB and an INL of + 1.98/-1.98 LSB while consuming 16.8 μW.

1 February 2016 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
SCSeungnam Choi
Seungnam Choi
HSHyunwoo Son
Hyunwoo Son
JSJongshin Shin
Jongshin Shin
SLSang-Hyun Lee
Sang-Hyun Lee
BKByungsub Kim
Byungsub Kim
JSJae-Yoon Sim
Jae-Yoon Sim
This paper presents a continuous-rate reference-less clock and data recovery (CDR) circuit with an asynchronous baud-rate sampling to achieve an adaptive equalization as well as a data rate acquisition. The proposed scheme also enables the use of a successive approximation register (SAR) based approach in the frequency acquisition and results in a fast coarse lock process. The CDR guarantees a robust operation of a fine locking even in the presence of large input data jitter due to the adaptive equalization and a jitter-tolerable rotation frequency detector (RFD) that eliminates a dead-zone problem with a simple circuitry. The fabricated CDR in 65 nm CMOS shows a wide lock range of 0.65-to-10.5 Gb/s at a bit error rate (BER) of $10^{-12}$ . The CDR consumes 26 mW from a single supply voltage of 1 V at 10 Gb/s including the power consumption for equalizer. By an adaptive current bias control, the power consumption is also linearly scaled down with the data rate, exhibiting a slope of about 2 mW decrease per Gb/s.

11 January 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SCSeungnam Choi
Seungnam Choi
HKHwan-Seok Ku
Hwan-Seok Ku
HSHyunwoo Son
Hyunwoo Son
BKByungsub Kim
Byungsub Kim
HPHong-June Park
Hong-June Park
JSJae-Yoon Sim
Jae-Yoon Sim
This paper presents an asynchronous-clocking successive approximation register (SAR) analog-to-digital converter (ADC) suitable for ultralow-power fine-precision sensor applications whose signal bandwidth is in the kilohertz range. The performance-limiting issues of comparator noise and capacitor mismatch in SAR ADC are resolved by a residue integration scheme combined with a dynamic element matching (DEM), achieving a high resolution without imposing extra burden on the design of residue amplifier and comparator. The prototype 16-bit 2 kS/s SAR ADC is fabricated using 180-nm CMOS process in an area of 0.68 mm². Measurements show 84.6-dB signal to noise and distortion ratio and 98.2-dB spurious-free dynamic range at the Nyquist input frequency. The ADC dissipates 7.93 μW from supply voltage of 1.8 V and achieves a Schreier figure of merit of 165.6 dB.

19 May 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JZJianming Zhao
Jianming Zhao
YGYuan Gao
Yuan Gao
TZTan-Tan Zhang
Tan-Tan Zhang
HSHyunwoo Son
Hyunwoo Son
CHChun-Huat Heng
Chun-Huat Heng
In this article, a fully integrated capacitorless low-dropout regulator (LDO) is presented for Internet-of-Things (IoT) edge sensor application. To achieve sub-1-V operation and fast transient response with low quiescent current, the conventional operational transconductance amplifier (OTA)-based error amplifier (EA) is replaced with oscillator-based voltage-to-time converter and time-domain signal processing, including time-domain edge-based frequency comparator (FC) and event-driven voltage mode charge pump (CP). Compared with the conventional phase frequency detector (PFD), the proposed clock-edge-based FC achieved more than six times power reduction. Event-driven CP is adopted to drive analog power transistor and the transient response is enhanced by feedforward capacitor $C_{\mathrm {FD}}$ and coarse–fine CP control. To further reduce the power consumption, multi-voltage domain and clock frequency optimization are implemented. A prototype chip is fabricated in a standard 65-nm CMOS process. The design only consumes 310-nA quiescent current while achieving 0.5–1.2-V input range, $1.0\times 10^{6}$ load dynamic range, and 3-fs figure of merit (FoM).

4 August 2025 in IEEE Access
Verified
Journal Article
Open access
RSRubel Sarkar
Rubel Sarkar
YPYunho Park
Yunho Park
HPHaneul Park
Haneul Park
JWJunghyun Woo
Junghyun Woo
HSHyunwoo Son
Hyunwoo Son
Over the decades, significant research on renewable energy systems (RESs) and their diverse applications has been conducted. Various RESs, including fuel cells (FCs), solar, wind, biomass, and hydroenergy, have emerged as sustainable substitutes for fossil fuels. Unlike fossil fuels, these renewable energy sources are environmentally friendly, applicable to rural areas, user-friendly, and cost-effective. Various sectors have adopted these energy sources based on their specific requirements and applications. Recently, FCs, particularly proton exchange membrane FCs (PEMFCs), have been employed in various industrial sectors, notably in hybrid electric vehicles. Additionally, PEMFCs have significantly transformed the marine industry. To enhance performance, energy storage system (ESS) components, such as batteries and supercapacitors, are often combined with PEMFCs to create hybrid energy storage systems (HESSs). HESSs can mitigate sudden fluctuations in load demand, especially when FCs alone are insufficient to meet power requirements. Various modeling techniques have been proposed to effectively configure HESSs. However, a critical challenge is to ensure efficient power sharing among the different ESSs. For this purpose, numerous research articles on optimizing the performance of HESS control strategies have been published. These strategies have been categorized into groups based on their specific applications. This article provides a comprehensive review by summarizing, elucidating, and consolidating the characteristics, limitations, future directions, and real-time applications of various HESS converter topologies and energy management systems by analyzing current and previous studies.