Hong-June Park

Prof. Hong-June Park

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 October 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
YJYoungwoo Ji
Youngwoo Ji
JLJungho Lee
Jungho Lee
BKByungsub Kim
Byungsub Kim
HPHong-June Park
Hong-June Park
JSJae-Yoon Sim
Jae-Yoon Sim
This article presents a methodology to design a circuit to compensate for process skew by exploiting an inherent dimension-dependent effect of process skew on change in the threshold voltage. We design a voltage reference circuit with a hybrid architecture of bandgap reference (BGR) and CMOS reference, which generates a nominal voltage level of (bandgap - threshold). By compensating the process skew of the threshold term with the proposed dimension-induced effect as well as the temperature dependence, the circuit achieves the simultaneous benefits of BGR and CMOS references. For verification, the circuit was fabricated in three wafers of a 0.18-μm CMOS including extreme slow and fast corners. With an active area of 0.0045 mm², it consumes 192 pW at room temperature. Measurement from 45 chips (15 chips per wafer) shows untrimmed process/voltage/temperature variations of 0.53%, 0.020%/V, and 33 ppm/°C, respectively.

22 December 2008 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
KCKwang-Hee Choi
Kwang-Hee Choi
JSJung-Bum Shin
Jung-Bum Shin
JSJae-Yoon Sim
Jae-Yoon Sim
HPHong-June Park
Hong-June Park
A digitally controlled oscillator (DCO) for the all-digital phase-locked loop (ADPLL) with both the wide frequency range and the high maximum frequency was proposed by using the interpolation scheme at both the coarse and fine delay blocks of the DCO. The coarse block consists of two ladder-shaped coarse delay chains. The delay of the first one is an odd multiple of an inverter delay and that of the second one is an even multiple. An interpolation operation is performed at the second coarse delay chain, which reduces both the resolution of the coarse delay block and the delay range of the fine block to half. This increases the maximum output frequency of the DCO while it maintains the wide frequency range. The ADPLL with the proposed DCO was fabricated in a 0.18 mum CMOS process with the active area of 0.32 mm2 . The measured output frequency of the ADPLL ranges from 33 to 1040 MHz at the supply of 1.8 V. The measured rms and peak-to-peak jitters are 13.8 ps and 86.7 ps, respectively, at the output frequency of 950 MHz. The power consumption is 15.7 mW.

11 January 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SCSeungnam Choi
Seungnam Choi
HKHwan-Seok Ku
Hwan-Seok Ku
HSHyunwoo Son
Hyunwoo Son
BKByungsub Kim
Byungsub Kim
HPHong-June Park
Hong-June Park
JSJae-Yoon Sim
Jae-Yoon Sim
This paper presents an asynchronous-clocking successive approximation register (SAR) analog-to-digital converter (ADC) suitable for ultralow-power fine-precision sensor applications whose signal bandwidth is in the kilohertz range. The performance-limiting issues of comparator noise and capacitor mismatch in SAR ADC are resolved by a residue integration scheme combined with a dynamic element matching (DEM), achieving a high resolution without imposing extra burden on the design of residue amplifier and comparator. The prototype 16-bit 2 kS/s SAR ADC is fabricated using 180-nm CMOS process in an area of 0.68 mm². Measurements show 84.6-dB signal to noise and distortion ratio and 98.2-dB spurious-free dynamic range at the Nyquist input frequency. The ADC dissipates 7.93 μW from supply voltage of 1.8 V and achieves a Schreier figure of merit of 165.6 dB.

12 November 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
MLMinseob Lee
Minseob Lee
SKShinwoong Kim
Shinwoong Kim
HPHong-June Park
Hong-June Park
JSJae-Yoon Sim
Jae-Yoon Sim
This paper presents a synthesized fractional-N digital phase-locked loop (PLL) with a speculative dual-referenced interpolating time-to-digital converter (DI-TDC). The DI-TDC measures a fractional phase by referencing two adjacent quadrant boundaries which are given by a four-phase digitally controlled oscillator (DCO). It achieves a robust gain matching to the first order without need of any calibration. By predicting a time region of interest for the next TDC conversion, the power and area overheads for DI-TDC is minimized. Except for DCO and a reference delay chain, the PLL is implemented with register-transfer level (RTL) behavioral descriptions followed by an automated synthesis. It is fabricated in 28-nm CMOS with an active area of 0.0043 mm². The PLL shows a wide frequency lock range operating at a supply voltage from 0.3 to 1.2 V, achieving a stable figure-of-merit of better than -220 dB for a supply voltage above 0.6 V.

27 June 2013 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SLSeon-Kyoo Lee
Seon-Kyoo Lee
BKByungsub Kim
Byungsub Kim
HPHong-June Park
Hong-June Park
JSJae-Yoon Sim
Jae-Yoon Sim
This paper presents an adaptive far-end crosstalk cancellation scheme for a single-ended parallel receiver. The adaptation engine is embedded in a single representative channel CDR, and the receiver efficiently reduces the crosstalk noise with a minimal cost in hardware and power consumption. In addition, the proposed scheme can be applied to any given CDR and equalizing circuits. The receiver is fabricated in 0.13 μm CMOS technology and achieves a reduction of FEXT-induced jitter up to 75%. The receiver consumes 65 mW at 5 Gb/s (4.3 mW/Gb/s/pin) including a PLL for global clock distribution.

18 September 2017 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
IYIl-Min Yi
Il-Min Yi
MCMin-Kyun Chae
Min-Kyun Chae
SHSeok-Hun Hyun
Seok-Hun Hyun
SBSeung-Jun Bae
Seung-Jun Bae
JCJung-Hwan Choi
Jung-Hwan Choi
HPHong-June Park
Hong-June Park
A time-based (TB) receiver (RX) with a 2-tap TB decision feedback equalizer (DFE) is proposed for mobile DRAM interface. The TB RX consists of a voltage-to-time converter (VTC), a TB DFE, and a time comparator. The VTC converts the RX input voltage to a time difference between two VTC outputs by using the difference in clock-to-Q delays between two latches with different input offset voltages. The TB DFE inserts an additional delay to one of the two VTC outputs and bypasses the other VTC output to increase the time opening. The time comparator makes a decision with the first arriving edge of the two outputs of the TB DFE. While the feedback loop delay must be less than 1 UI for proper operation in the conventional voltage-based DFE, the TB DFE allows the feedback loop delay up to 1.43 UI in this paper. A transmitter (TX) transmits a single-ended signal of 200-mV swing by using an n-over-n voltage-mode driver. The transceiver in a 65-nm CMOS process achieves a 12.5 Gb/s with a 0.8-V supply through a 15-inch FR-4 channel of 14-dB loss. The TX and RX chip consume 4.3 and 3.4 mA, respectively. The energy efficiency is 0.49 pJ/b.