Tibial bone stress injury is a common overuse injury experienced by runners, which results from repetitive tissue forces. Wearable sensor systems (wearables) that monitor tibial forces could help understand and reduce injury incidence. However, there are currently no validated wearables that monitor tibial bone forces. Previous work using simulated wearables demonstrated accurate tibial force estimates by combining a shoe-worn inertial measurement unit (IMU) and pressure insole with a trained algorithm. This study aimed assessed how accurately tibial bone forces could be estimated with existing wearables. Nine recreational runners ran at a series of different speeds and slopes, and with various stride patterns. Shoe-worn IMU and insole data were input into a trained algorithm to estimate peak tibial force. We found an average error of 5.7% in peak tibial force estimates compared with lab-based estimates calculated using motion capture and a force instrumented treadmill. Insole calibration procedures were essential to achieving accurate tibial force estimates. We concluded that a shoe-worn, multi-sensor system is a promising approach to monitoring tibial bone forces in running. This study adds to the literature demonstrating the potential of wearables to monitor musculoskeletal forces, which could positively impact injury prevention, and scientific understanding.
Low back disorders (LBDs) are a leading occupational health issue. Wearable sensors, such as inertial measurement units (IMUs) and/or pressure insoles, could automate and enhance the ergonomic assessment of LBD risks during material handling. However, much remains unknown about which sensor signals to use and how accurately sensors can estimate injury risk. The objective of this study was to address two open questions: (1) How accurately can we estimate LBD risk when combining trunk motion and under-the-foot force data (simulating a trunk IMU and pressure insoles used together)? (2) How much greater is this risk assessment accuracy than using only trunk motion (simulating a trunk IMU alone)? We developed a data-driven simulation using randomized lifting tasks, machine learning algorithms, and a validated ergonomic assessment tool. We found that trunk motion-based estimates of LBD risk were not strongly correlated (r range: 0.20–0.56) with ground truth LBD risk, but adding under-the-foot force data yielded strongly correlated LBD risk estimates (r range: 0.93–0.98). These results raise questions about the adequacy of a single IMU for LBD risk assessment during material handling but suggest that combining an IMU on the trunk and pressure insoles with trained algorithms may be able to accurately assess risks.
Achilles tendon overuse injuries are common for long-distance runners. Ankle exos (exoskeletons and exosuits) are wearable devices that can reduce Achilles tendon loading and could potentially aid in the rehabilitation or prevention of these injuries by helping to mitigate and control tissue loading. However, most ankle exos are confined to controlled lab testing and are not practical to use in real-world running. Here, we present the design of an unpowered ankle exo aimed at reducing the load on the Achilles tendon during running while also overcoming key usability challenges for runners outside the lab. We fabricated a 500-gram ankle exo prototype that attaches to the outside of a running shoe. We then evaluated the reliability, acceptability, transparency during swing phase, and offloading assistance provided during treadmill and outdoor running tests. We found that the exo prototype reliably assisted 95–99% of running steps during indoor and outdoor tests, was deemed acceptable by more than 80% of runners in terms of comfort and feel, and did not impede natural ankle dorsiflexion during leg swing for 86% of runners. During indoor tests, the exo reduced peak Achilles tendon loads for most participants during running; however, reductions varied considerably, between near zero and 12%, depending on the participant, condition (speed and slope) and the precise tendon load metric used. This next-generation ankle exo concept could open new possibilities for longitudinal and real-world research on runners, or when transitioning into the return-to-sport phase after an Achilles tendon injury.
Tibia shaft fractures are common lower extremity fractures that can require surgery and rehabilitation. However, patient recovery is often poor, partly due to clinicians’ inability to monitor bone loading, which is critical to stimulating healing. We envision a future of patient care that includes at-home monitoring of tibia loading using pressure-sensing insoles. However, one issue is missing portions of daily loading due to limited insole wear time (e.g., not wearing shoes all day). Here, we introduce a method for overcoming this issue with a wrist-worn fitness tracker that can be worn all day. We developed a model to estimate tibia loading from fitness tracker data and evaluated its accuracy during 10-h remote data collections (N = 8). We found that a fitness tracker, with trained and calibrated models, could effectively supplement insole-based estimates of bone loading. Fitness tracker-based estimates of loading stimulus—the minute-by-minute weighted impulse of tibia loading—showed a strong fit relative to insole-based estimates (R2 = 0.74). However, insoles needed to be worn for a minimum amount of time for accurate estimates. We found daily loading stimulus errors less than 5% when insoles were worn at least 25% of the day. These findings suggest that a multi-sensor approach—where insoles are worn intermittently and a fitness tracker is worn continuously throughout the day—could be a viable strategy for long-term, remote monitoring of tibia loading in daily life.