Tibial bone stress injury is a common overuse injury experienced by runners, which results from repetitive tissue forces. Wearable sensor systems (wearables) that monitor tibial forces could help understand and reduce injury incidence. However, there are currently no validated wearables that monitor tibial bone forces. Previous work using simulated wearables demonstrated accurate tibial force estimates by combining a shoe-worn inertial measurement unit (IMU) and pressure insole with a trained algorithm. This study aimed assessed how accurately tibial bone forces could be estimated with existing wearables. Nine recreational runners ran at a series of different speeds and slopes, and with various stride patterns. Shoe-worn IMU and insole data were input into a trained algorithm to estimate peak tibial force. We found an average error of 5.7% in peak tibial force estimates compared with lab-based estimates calculated using motion capture and a force instrumented treadmill. Insole calibration procedures were essential to achieving accurate tibial force estimates. We concluded that a shoe-worn, multi-sensor system is a promising approach to monitoring tibial bone forces in running. This study adds to the literature demonstrating the potential of wearables to monitor musculoskeletal forces, which could positively impact injury prevention, and scientific understanding.
27 May 2019 in Scandinavian Journal of Medicine & Science in Sports
A decrease in speed when sprinting on the bend compared with the straight has been attributed to kinetic, kinematic and spatiotemporal modifications. Although maximal speed is dependent on an athlete’s ability to accelerate, there is limited research investigating the acceleration phase of bend sprinting. This study used a lower limb and trunk marker set with 15 optoelectronic cameras to examine kinematic and spatiotemporal variables of the lower limb during sprinting on the bend and straight. Nine sprinters completed up to six 30 m maximal effort trials in bend (radius 36.5 m, lane one) and straight conditions. An increase in body lateral lean at touchdown resulted in a number of asymmetric kinematic modifications. Whilst the left limb demonstrated a greater peak hip adduction, peak hip internal rotation and peak ankle eversion on the bend compared with the straight, the right limb was characterised by an increase in peak hip abduction. These results demonstrate that kinematic modifications start early in the race and likely accumulate, resulting in greater modifications at maximal speed. It is recommended that strength and conditioning programmes target the hip, ankle and foot in the non-sagittal planes. In addition, sprint training should prioritise specificity by occurring on the bend.
Low back disorders (LBDs) are a leading occupational health issue. Wearable sensors, such as inertial measurement units (IMUs) and/or pressure insoles, could automate and enhance the ergonomic assessment of LBD risks during material handling. However, much remains unknown about which sensor signals to use and how accurately sensors can estimate injury risk. The objective of this study was to address two open questions: (1) How accurately can we estimate LBD risk when combining trunk motion and under-the-foot force data (simulating a trunk IMU and pressure insoles used together)? (2) How much greater is this risk assessment accuracy than using only trunk motion (simulating a trunk IMU alone)? We developed a data-driven simulation using randomized lifting tasks, machine learning algorithms, and a validated ergonomic assessment tool. We found that trunk motion-based estimates of LBD risk were not strongly correlated (r range: 0.20–0.56) with ground truth LBD risk, but adding under-the-foot force data yielded strongly correlated LBD risk estimates (r range: 0.93–0.98). These results raise questions about the adequacy of a single IMU for LBD risk assessment during material handling but suggest that combining an IMU on the trunk and pressure insoles with trained algorithms may be able to accurately assess risks.
Exoskeletons and exosuits (exos) are wearable devices that physically assist movement. User comfort is critically important for societal adoption of exos. Thermal comfort (a person’s satisfaction with their thermal environment) represents a key design challenge. Exos must physically attach/interface to the body to apply forces, and these interfaces inevitably trap some heat. It is envisioned that thermal comfort could be improved by designing mode-switching exo interfaces that temporarily loosen around a body segment when assistive forces are not being applied. To inform exo design, a case series study (N = 4) based on single-subject design principles was performed. Our objective was to assess individual responses to skin temperature and thermal comfort during physical activity with a Loose leg-sleeve interface compared with a Form-Fitting one, and immediately after a Form-Fitting sleeve switched to Loose. Skin under the Loose sleeve was 2–3 °C (4–6 °F) cooler after 25 min of physical activity, and two of four participants reported the Loose sleeve improved their thermal comfort. After completion of the physical activity, the Form-Fitting sleeve was loosened, causing a 2–4 °C (3–8 °F) drop in skin temperature underneath for all participants, and two participants to report slightly improved thermal comfort. These findings confirmed that an exo that can quickly loosen its interface when assistance is not required—and re-tighten when it is— has the potential to enhance thermal comfort for some individuals and environments. More broadly, this study demonstrates that mode-switching mechanisms in exos can do more than adjust physical assistance: they can also exploit thermodynamics and facilitate thermoregulation in a way that enhances comfort for exo users.