Anas Abid Mattie

Mr. Anas Abid Mattie

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 August 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
Mahmoud MoradiMahmoud Moradi
Mahmoud Moradi
Omid MehrabiOmid Mehrabi
Omid Mehrabi
FRFakhir A. Rasoul
Fakhir A. Rasoul
AMAnas Abid Mattie
Anas Abid Mattie
Friedemann SchaberFriedemann Schaber
Friedemann Schaber
RKRasoul Khnadan
Rasoul Khnadan
The rapid advancement of additive manufacturing (AM) technologies has provided new avenues for creating three-dimensional (3D) parts with intricate geometries. Fused Deposition Modeling (FDM) is a prominent technology in this domain, involving the layer-by-layer fabrication of objects by extruding a filament comprising a blend of polymer and metal powder. This study focuses on the FDM process using a filament of Copper–Polylactic Acid (Cu-PLA) composite, which capitalizes on the advantageous properties of copper (high electrical and thermal conductivity, corrosion resistance) combined with the easily processable thermoplastic PLA material. The research delves into the impact of FDM process parameters, specifically, infill percentage (IP), infill pattern (P), and layer thickness (LT) on the maximum failure load (N), percentage of elongation at break, and weight of Cu-PLA composite filament-based parts. The study employs the response surface method (RSM) with Design-Expert V11 software. The selected parameters include infill percentage at five levels (10, 20, 30, 40, and 50%), fill patterns at five levels (Grid, Triangle, Tri-Hexagonal, Cubic-Subdivision, and Lines), and layer thickness at five levels (0.1, 0.2, 0.3, 0.4, and 0.5 mm). Also, the optimal factor values were obtained. The findings highlight that layer thickness and infill percentage significantly influence the weight of the samples, with an observed increase as these parameters are raised. Additionally, an increase in layer thickness and infill percentage corresponds to a higher maximum failure load in the specimens. The peak maximum failure load (230 N) is achieved at a 0.5 mm layer thickness and Tri-Hexagonal pattern. As the infill percentage changes from 10% to 50%, the percentage of elongation at break decreases. The maximum percentage of elongation at break is attained with a 20% infill percentage, 0.2 mm layer thickness, and 0.5 Cubic-Subdivision pattern. Using a multi-objective response optimization, the layer thickness of 0.152 mm, an infill percentage of 32.909%, and a Grid infill pattern was found to be the best configuration.

6 July 2023 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
AMAnas Abid Mattie
Anas Abid Mattie
SESafeen Yaseen Ezdeen
Safeen Yaseen Ezdeen
GKGawhar Ibraheem Khidhir
Gawhar Ibraheem Khidhir
Solid state joining techniques are increasingly used in joining different types of materials, in this work TP347HFG austenitic stainless steel will be welded with HiPerFer ferritic stainless-steel alloy due to their similarity in their properties to some extent after making heat treatment to ferritic alloy in addition to difference in their cost which save for economic reasons. In this work, a three-dimensional finite element model was developed. The thermal analysis and profiles between process parameters were predicted by using an ANSYS software tool. Design of experiments by Anova was used to examinate the simulation results and to evaluate contribution ratio of each parameter on responses, while grey relational analysis was used to specify the optimum trial. It was observed that trial 11 give best results (A4B2C1D1) which got higher grey relational grade. It was concluded that the friction pressure and friction time have more impact on interface temperature, whereas forging pressure and friction time affect the equivalent Von-Mises stress directly. The speed and forging pressure have a more influence on total deformation. It was also concluded that the temperature was fade out by diverging toward the end of specimen and the amount of decrease in temperature is less in ferritic side. The amount of flash extruded from both steels are approximately similar due to similarity in properties as heat treatment of ferritic alloy had been achieved. The investigation results show that trial 8 achieved highest Von-Mises stress (300 MPa) while trial 7 induced lower stress (255 MPa), maximum deformation was found equivalent to 0.012 mm with trial 16 whereas, it was found (0.008 mm) with trial 11 which were both less than the allowable deformation in end application. Tensile strength of weld joint was found equivalent to 80% of softer base metal. The hardness of optimum trial was equivalent to 156 HB.

28 August 2019 in Mechanics
Verified
Journal Article
Open access
PDF file
AMAnas Abid Mattie
Anas Abid Mattie
AAAsad Alizadeh
Asad Alizadeh
The interaction between incompressible fluids and elastic and rigid boundaries is seen in many medical, engineering and natural issues. The immersed interface method is used as a non-conforming meshes method to simulate such problems. In this method, the effect of the presence of a body immersed in a fluid is considered by adding a force term to the Navier-Stokes equations. An important advantage of this method is that there is no compulsion to adapt the fluid grids and the boundary grids. First, the flow around a circular cylinder was simulated. As the Reynolds number rises, the vortex dimensions become larger and, as a result, the separation angle of the flow increases. Also, with the Reynolds number increasing, the drag coefficient decreases and the Strouhal number increases and the flow separated from cylinder and two symmetrical vortices is generated behind the cylinder. Then, the behavior of an elastic boundary in shear flow was investigated. It was observed that by increasing bending modulus (increasing stiffness) of body the shape change of the boundary decreases. As well as the tank-treading motion is also observed that this type of movement has been confirmed in experiments.Also observed that the sick cell makes smaller defor-mation, while the normal cell is more deformed and easier passes the stenosis. This results in reduction of the flow rate in stenosis.This behavior is caused by a type of dis-ease called sickle cell anemia.