Friedemann Schaber

Dr. Friedemann Schaber

Art, Science and Technology, University of Northampton, Northampton, UK
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 August 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
Mahmoud MoradiMahmoud Moradi
Mahmoud Moradi
Omid MehrabiOmid Mehrabi
Omid Mehrabi
FRFakhir A. Rasoul
Fakhir A. Rasoul
AMAnas Abid Mattie
Anas Abid Mattie
Friedemann SchaberFriedemann Schaber
Friedemann Schaber
RKRasoul Khnadan
Rasoul Khnadan
The rapid advancement of additive manufacturing (AM) technologies has provided new avenues for creating three-dimensional (3D) parts with intricate geometries. Fused Deposition Modeling (FDM) is a prominent technology in this domain, involving the layer-by-layer fabrication of objects by extruding a filament comprising a blend of polymer and metal powder. This study focuses on the FDM process using a filament of Copper–Polylactic Acid (Cu-PLA) composite, which capitalizes on the advantageous properties of copper (high electrical and thermal conductivity, corrosion resistance) combined with the easily processable thermoplastic PLA material. The research delves into the impact of FDM process parameters, specifically, infill percentage (IP), infill pattern (P), and layer thickness (LT) on the maximum failure load (N), percentage of elongation at break, and weight of Cu-PLA composite filament-based parts. The study employs the response surface method (RSM) with Design-Expert V11 software. The selected parameters include infill percentage at five levels (10, 20, 30, 40, and 50%), fill patterns at five levels (Grid, Triangle, Tri-Hexagonal, Cubic-Subdivision, and Lines), and layer thickness at five levels (0.1, 0.2, 0.3, 0.4, and 0.5 mm). Also, the optimal factor values were obtained. The findings highlight that layer thickness and infill percentage significantly influence the weight of the samples, with an observed increase as these parameters are raised. Additionally, an increase in layer thickness and infill percentage corresponds to a higher maximum failure load in the specimens. The peak maximum failure load (230 N) is achieved at a 0.5 mm layer thickness and Tri-Hexagonal pattern. As the infill percentage changes from 10% to 50%, the percentage of elongation at break decreases. The maximum percentage of elongation at break is attained with a 20% infill percentage, 0.2 mm layer thickness, and 0.5 Cubic-Subdivision pattern. Using a multi-objective response optimization, the layer thickness of 0.152 mm, an infill percentage of 32.909%, and a Grid infill pattern was found to be the best configuration.

14 September 2026 in Polymers
Verified
Journal Article
Open access
PDF file
HGHorea-Stefan Goia
Horea-Stefan Goia
Florin PopișterFlorin Popișter
Florin Popișter
Corina J. BîrleanuCorina J. Bîrleanu
Corina J. Bîrleanu
RAZVAN UDROIURAZVAN UDROIU
RAZVAN UDROIU
Friedemann SchaberFriedemann Schaber
Friedemann Schaber
MPMarius Pustan
Marius Pustan
Fused filament fabrication (FFF) is increasingly employed for functional components subjected to sliding contact, for which friction and wear determine service life as decisively as static strength. Tribological characterization of fiber-reinforced polyamide 12 has been conducted predominantly under dry sliding, and the influence of the lubrication regime on the contrast between reinforcement types remains insufficiently established. The present study investigated carbon fiber (PA12-CF) and glass fiber (PA12-GF) reinforced polyamide 12, both processed by FFF, under dry sliding and under two protic ionic liquid lubricants, bis (2-hydroxyethyl) ammonium succinate (MSu) and bis (2-hydroxyethyl) ammonium citrate (MCi). Discs were tested against a 100Cr6 bearing steel counterface on an Anton Paar TRB3 tribometer at a fixed normal load of 20 N, with sliding speeds of 0.5, 0.75 and 1.0 m/s for 60 min each. The coefficient of friction (COF) and the contact-point temperature were recorded throughout, the specific wear rate was obtained by contact profilometry, and worn surfaces were examined by scanning electron microscopy with energy dispersive X-ray analysis. MCi held the mean COF at 0.023 for both composites, against a dry mean of 0.071 across the study, whereas MSu increased the mean to 0.25 and produced the highest wear rates, concurrent with an increase in viscosity during testing. Reinforcement type governed the morphology of the worn surface consistently, yet lubricant selection proved more consequential than material selection.

4 June 2019
Verified
Book Chapter
Closed access
PDF file
CLCaroline Lloyd
Caroline Lloyd
Friedemann SchaberFriedemann Schaber
Friedemann Schaber