This paper presents the design and evaluation of a new axial-flux low-speed and high-torque matrix-rotor induction machine. Iron wires embedded in a cupper matrix comprise the solid rotor structure. Specific design and sizing equations are provided focusing on key rotor parameters: the iron/copper ratio and iron wire diameter. The analysis was carried out through analytical equations and three-dimensional finite element simulations. Based on the proposed design guidelines, A 20 HP, 250 rpm prototype was built and evaluated for experimental validation. Good concordance was obtained between the different stages of the matrix-rotor induction machine design: the initial sizing recommendations, finite element simulations and experimental results. Moreover, the proposed machine is suitable for low-speed high-torque applications, although there is room for further optimization depending on specific application needs.
This article presents an accurate analytical model (AM) for synchronous reluctance machine (SynRM) that incorporates the effect of stator slots on the air gap flux density and torque waveforms. From the formulation of magnetic potential in the air gap for both the stator and rotor, the flux density is obtained, considering the first harmonic of the flux density and the electric loading, the average torque is calculated using the Lorentz’s force. The ripple torque is obtained from the energy stored in magnetic circuit. The method is developed for a rotor with one flux barrier per pole and then extended to a larger number of barriers. To validate the results obtained by the AM proposed finite element analysis have been carried out. Several comparisons have been derived considering different rotor positions as well as different harmonic orders, and the pros and cons of the method are highlighted. The model performs fast and can predict results with high accuracy, and can be adopted to speed up the preliminary design and optimizations of this type of motors, with respect to finite element. In addition, from the analytical expressions it is possible to obtain all the correlations between electrical, magnetic, and geometrical characteristics of the machine, with the advantage of enabling a faster machine design.
In this paper, a discrete skew methodology is presented to understand the effect of skewing angle on electromagnetic torque in SynRM design. A new approach is proposed to estimate the amplitude of each torque ripple component as a function of skewing angle. The reduction factor for each harmonic component is derived in general form, allowing for the determination of overall torque ripple waveform. The validity of the proposed method is evaluated through the examination of two SynRMs, resulting in a torque ripple reduction of up to 70%. The results obtained through the use of a proposed analytical ripple reduction estimator and FEA evaluation showed good agreement. The proposed skewing technique was applied on a previously optimized triple-barrier SynRM with a positive outcome: a consistent torque ripple reduction tackling relevant harmonic components. The analysis of harmonic distribution of torque ripple is mandatory for the selection of the optimal skewing strategy when following the proposed method, with two-step skewing recommended for mostly-purely-sinusoidal torque waveforms, and multi-step skewing recommended for machines with multiple higher-magnitude harmonic components.
Several studies have focused on modeling and analyzing the impact of rotor faults in conventional low-pole-count machines, while related research on low-speed high-torque (LSHT) machines with a high pole count remains limited. In these machines, the combination of low speed, high inertia, and high torque levels presents a critical application for advanced diagnosis techniques. The present paper aims to describe and quantify the impact of rotor faults on the performance of LSHT machine types during the design stage. Specifically, 10-pole and 16-pole synchronous reluctance machines (SynRMs), permanent magnet synchronous machines (PMSMs), and squirrel-cage induction machines (SCIMs) are assessed by means of detailed 2D simulations. The effects of eccentricity, broken rotor bars, and partial demagnetization are studied, with a focus on performance variations. The results show that LSHT PMSMs are not significantly affected by the partial demagnetization of a few magnets, and the same holds true for common faults in SynRMs and SCIMs. Nonetheless, a significant increase in torque ripple was observed for all evaluated faults, with different origins and diverse effects on the torque waveform, which could be hard or invasive to analyze. Furthermore, it was concluded that specialized diagnosis techniques are effectively required for detecting the usual faults in LSHT machines, as their effect on major performance indicators is mostly minimal.
Tolerance analysis on synchronous reluctance machines (SynRM) is mandatory if accurate refinements of the rotor structure are adopted, a must for low-ripple applications However, the impact of manufacturing/dimensional tolerances or material degradation has been scarcely included in the design steps for SynRMs obeying complexity and time-requirement reasons. The paper provides an analysis of rotor barrier dimensional allowances in synchronous reluctance machines by utilizing a semi-analytical approach. This method is not only fast yet it also generates a substantial number of results that allows to evaluate the influence of dimensional deviations on the machine’s performance. The proposed performance evaluation method is validated in four machines by direct finite element (FE) simulations, showing good agreement and low computational burden. Once validated, the method is applied to perform a brute-force search in a single-barrier 4-pole machine with different combinations of dimensional allowances, obtaining a significant reduction in computational time compared to traditional direct FE evaluation. The paper concludes with a description of the proposed methodology and its applicability to other SynRM designs. This opens the possibility of quickly analyzing tolerances in SynRMs and improving their performance by evaluating different dimensions and position of flux barriers.
1
7 January 2026 in Journal of Electrical Engineering & Technology