Corrosion significantly impacts the welding of dissimilar components, leading to a decrease in the lifespan of products. The primary aim of this research is to examine the corrosion behavior of the weld region in dissimilar welding of Inconel 625 and AISI 316L plates with a thickness of 20 mm. The plates are weld together by using continuous current gas tungsten arc welding (CCGTA) and pulsed current gas tungsten arc welding (PCGTAW) methods. The process employs ERNiCr-3, TIG 316L, and a twisted combination of both filler metals (ERNiCr-3+TIG 316L). Specimens with dimensions of 12 mm × 20 mm × 42 mm are obtained by cutting the weld samples for corrosion tests. The divided parts are each submerged in a 100 ml pool of sulfuric acid and are maintained for a combined duration of 240 h. A weight loss investigation is undertaken, in addition to metallurgical characterizations of the specimens. Energy Dispersive Spectroscopy (EDS) in conjunction with Scanning Electron Microscopy (SEM) are utilized to conduct metallurgical investigations. It is observed that twisted filler metal and CCGTA welding method results in the highest amount of mass loss. The least corroded sample is obtained by using twisted filler metal combined with PCGTA welding method.
15 September 2017 in Strojniški vestnik - Journal of Mechanical Engineering
There are two major problems with fiber-reinforced polymer (FRP) composites during their machining that need to be addressed. The first concern is the delamination and formation of burrs at machined edges, and the second is the effects of aging leading to mechanical deterioration. In this study, carbon FRP (CFRP) and aramid FRP (AFRP) composites were manufactured by vacuum infusion method and aged for 2 years under natural environmental conditions. Piercing with three different clearances (1%, 5%, and 10% of sheet thickness) and speed of 4 m/s were performed. Additionally, conventional drilling was carried out at a feed rate of 0.2 m/min. The highest delamination factor difference between piercing and drilling processes was calculated as 7.3% and 13.9% for CFRP and AFRP, respectively. The highest burr amounts for AFRP and CFRP composites were obtained as 91.5% and 39% at 10% clearance for piercing process and 123% and 32.1% for drilling process, respectively. Compared with drilling, piercing generates less burr formation except for CFRP composites in the case of 10% clearance and more precise hole production. It is understood that piercing results significantly improve when smaller clearances up to 5% of the sheet thickness are utilized.
18 September 2023 in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Fiber reinforced polymer (FRP) composites are being used in a variety of areas. These materials need to be processed with some machining methods according to their usage areas, but their machinability is difficult. In this study, drilling is performed on glass fiber reinforced polymer (GFRP) composite produced by pultrusion with coated and uncoated drill. Then, surface roughness (SR), delamination factor (Fd) and thrust forces were investigated. Microstructures of chips formed during drilling were investigated and their effects on surface roughness were determined. Three distinct feed rates and cutting speeds were selected as machining parameters. Investigations showed that feed rate had a more significant effect on surface roughness, delamination factor and thrust force. It was understood that when the cutting speed increased, the surface roughness, thrust force and delamination factor decreased. Better results were obtained with TiN coated drills compared to uncoated drills.
1 December 2023 in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Increasing supply chain problems in recent years have a negative impact on costs in many areas. Due to the global crisis, raw material prices increased and the manufacturing sector was seriously affected. Production planning and material saving should be done correctly in order to minimize the losses in the manufacturing sector. The most efficient way to reduce production costs is to use suitable cutting tools and choose the right machining parameters. In this study, the drilling of AISI D2 steel, which is widely used in the mold industry, was examined and optimum machining parameters were determined. TiN coated drills are used for drilling operations. The effects of machining parameters on Surface Roughness (Ra) and Thrust Force (Fz) were investigated by Taguchi and ANOVA. Surface roughness and thrust force values during drilling were measured. Thrust force values were also analyzed numerically by the Finite Element (FE) method. Ra and Fz were also low at low feed rate and low cutting speeds. While the feed rate affected Ra the most, the Fz affected the cutting speed the most. The lowest Ra and Fz were at 30 mm/min feed rate and 25 m/min cutting speed. According to the ANOVA, it was determined that the machining parameters were effective on both Ra and Fz. R2 values for Ra and Fz are calculated over 95%.
Additively manufactured thermoplastic polyurethane (TPU 95A) is widely used in engineering, yet its machining behavior remains insufficiently explored. This study investigates the post-processing machinability of FDM-fabricated TPU 95A using CNC milling, with a particular focus on material removal rate (MRR) and surface roughness (Ra). A full factorial design of experiments (81 runs) is conducted, considering four input parameters such as spindle speed (N; 2000, 4000, 6000 rpm) and feed rate (F; 100, 200, 300 mm/min) on the CNC vertical machining center, together with infill density (ϕ; 33%, 66%, 100%) and layer thickness (LT; 1.0, 1.5, 2.0 mm). MRR is modeled and optimized across all densities, achieving strong fit (R2 = 0.94; Adj-R2 = 0.93). The optimum conditions are found to be MRR ≈ 1251 mm3/min at F = 300 mm/min, ϕ = 100%, N ≈ 3500 rpm and LT ≈ 1.05 mm. Ra can only be measured for 100% infill specimens, as lower infill surfaces violate profile measurement requirements. Its regression model shows weak explanatory power (R2 = 0.14; Adj-R2 = 0.03) and is excluded from optimization. Instead, Ra is reported descriptively: milling reduced roughness from ≈25–30 μm (as-printed) to ≈13.8 μm under favorable conditions. Overall, the study highlights machining’s role in the hybrid manufacturing practice.