Natural fibers extracted from plants are preferred as an alternative to synthetic products. The main reasons for this preference are their affordable cost, light weight and good mechanical properties. However, finding new natural raw materials is challenging due to growth limitations in different geographical areas. Platanus orientalis L. (Eastern plane tree) is a tree with abundant fruits that can grow in many regions of the world. The aim of this study was to determine the mechanical (tensile strength, tensile modulus, elongation), physical (density, fiber diameter) and chemical (cellulose, hemicellulose and lignin) properties of Platanus orientalis L. fruit’s stem by fiber extraction from the stems of the tree. It was determined that the extracted fiber had good mechanical properties and cellulose content of 42.03%. As a result of thermogravimetric analysis, it was determined that the plane tree fruit’s stem fiber had thermal resistance of up to 299 °C. The tensile strength value was 157.76 MPa, the tensile modulus value was 1.39 GPa and the elongation value was 22.01%. It was determined that it is suitable for use in fiber reinforcement in thermoplastic-based composites at temperatures below 299 °C. According to the results obtained by the mechanical, chemical and physical analysis of Platanus orientalis L. fruit’s stem fiber (PoLfs), it could be recommended as a suitable alternative as a reinforcing fiber in thermoplastic and thermoset composites.
1 June 2023 in Transactions of the Canadian Society for Mechanical Engineering
There are two major problems with fiber-reinforced polymer (FRP) composites during their machining that need to be addressed. The first concern is the delamination and formation of burrs at machined edges, and the second is the effects of aging leading to mechanical deterioration. In this study, carbon FRP (CFRP) and aramid FRP (AFRP) composites were manufactured by vacuum infusion method and aged for 2 years under natural environmental conditions. Piercing with three different clearances (1%, 5%, and 10% of sheet thickness) and speed of 4 m/s were performed. Additionally, conventional drilling was carried out at a feed rate of 0.2 m/min. The highest delamination factor difference between piercing and drilling processes was calculated as 7.3% and 13.9% for CFRP and AFRP, respectively. The highest burr amounts for AFRP and CFRP composites were obtained as 91.5% and 39% at 10% clearance for piercing process and 123% and 32.1% for drilling process, respectively. Compared with drilling, piercing generates less burr formation except for CFRP composites in the case of 10% clearance and more precise hole production. It is understood that piercing results significantly improve when smaller clearances up to 5% of the sheet thickness are utilized.
This study aimed to exploit the superior properties of TiO2, ZnO, SiO2 and Al2O3 inorganic materials to combine them under pressure and investigate their mechanical properties. The hot pressing technique was used to produce new materials. Varying amounts of alumina such as 0, 5, 10, 20 and 30 wt% in compounds was considered. The produced materials were characterized by SEM, EDS and XRD analyses. The microhardness properties of the materials were studied, and their tribological properties under different wear loads, i.e., 10 N, 20 N and 30 N, were investigated for every specimen. In XRD analysis, it was observed that no significant new peaks were formed regarding increasing alumina content. The SEM and EDS characterization analyses showed that the materials had a two-phase structure with complex boundaries, and no clear grain boundaries were formed. Moreover, the elements in the EDS analyses and the compounds in the XRD analyses were found to be in line with each other. In wear tests, it was seen that as the wear load increased, the depth and width of the wear track increased. The highest weight loss under different wear loads was obtained for the Ti55Si15Zn20Al10 material. It was determined that as the Al2O3 wt% increased over 10 wt%, the weight losses decreased. It was observed that there was an increase in the microhardness value generally depending on the increase of alumina content in compounds.
4 February 2017 in Journal of Sol-Gel Science and Technology
In this study, different wt% of B4C material added to TiO2, ZnO, and SiO2 materials known with distinguished properties by hot-pressing method to produce new materials. Characterization of the materials was performed by using XRD, SEM and EDS. The micro-hardness of the materials was measured and the wear characteristics of B4C-added materials were determined by subjecting them to wear loads of 5 N, 10 N and 15 N. In XRD, it was observed that the intensity of the peak was decreased depending on the increase in B4C content. In SEM, it was determined that there was a two-phase structure with complex boundaries and indefinite grain boundary formation. Besides, it was determined that elements in the EDS and the compounds in the XRD supported each other. In wear analyses, it was seen that as the wear load increased, the depth and width of the wear track in all materials increased. Furthermore, as the weight ratio of B4C material in the composition was increased, the weight loss at different wear loads was decreased and the lowest weight loss was found in Ti45Si15Zn20B20 material. Moreover, it was observed that the wear track and its depth were inversely proportional to the increasing B4C content in the compound. Friction coefficients of the materials under 5 N wear load varied between 0.15–0.43, whereas under 10 N and 15 N wear load, it varied between 0.09–0.28 and 0.06–0.29, respectively. While the hardness value of B4C-free Ti60Si20Zn20 was 260 HV, the highest hardness value was seen in Ti45Si15Zn20B20 material as 1010 HV.