Grass cutting is necessary to prevent grass from diverting essential nutrients and water from crops. Usually, in hilly and mountainous areas, grass cutting is performed on steep slopes with an inclination angle of up to 60° (inclination gradient of 173%). However, such grass cutting tasks are dangerous owing to the unstable positioning of workers. For robots to perform these grass cutting tasks, slipping and falling must be prevented on inclined surfaces. In this study, a robot based on stable propeller control and four-wheel steering was developed to provide stable locomotion during grass cutting tasks. The robot was evaluated in terms of locomotion for different steering methods, straight motion on steep slopes, climbing ability, and coverage area. The results revealed that the robot was capable of navigating uneven terrains with steep slope angles. Moreover, no slipping actions that could have affected the grass cutting operations were observed. We confirmed that the proposed robot is able to cover 99.95% and 98.45% of an area on a rubber and grass slope, respectively. Finally, the robot was tested on different slopes with different angles in hilly and mountainous areas. The developed robot was able to perform the grass cutting task as expected.
Periodic inspections are necessary in maintaining concrete infrastructures. As efficient and low-cost inspection methods, visual inspection robots and hammering inspection robots to detect cracks and internal defects have been developed, respectively. However, these robots can perform only a single task. To realize multiple tasks by a robot, multiple measurement sensors must be installed considering the stability of the robot on the wall and measurement performance. Parameters, such as weight and size, must be considered to ensure the stability of the robot on the wall. We proposed a propeller-type wall-climbing robot that can capture images and perform hammering simultaneously while moving on the wall. The static model of robot was established by considering various parameters, such as the direction of the propeller’s thrust force, weight, and placement of the measurement sensors. This model increases the payload for sensor installation and enables movement on dusty concrete walls with a low friction coefficient. The image captured by the inspection robot was employed for crack detection and width estimation. We confirmed that the hammering sounds generated by the robot showed different frequency characteristics on clear and defective areas. The developed inspection robot can collect adequate data for concrete health monitoring.
1 January 2013 in Journal of Japan Society of Civil Engineers, Ser. A2 (Applied Mechanics (AM))
Quality evaluation of kindergarten classrooms is important for promoting teachers’ competencies and ensuring high-quality education. Currently, human observers physically visit kindergartens and provide assessments by observing classroom activities. However, rural areas suffer from a lack of observers, despite the high demand for quality evaluation. In this study, we proposed the use of telepresence robots in early childhood education and care, specifically for the evaluation of kindergarten classroom quality. A telepresence robot is a contemporary tool that provides both clear visibility of the teacher and the ability to hear interactions with children as a part of the classroom, while reducing the observer’s transportation cost and time. We conducted a field study in which observers evaluated the classroom both in-person and via telepresence robots. A total of 12 observation and rating scores were collected for both the quantitative and qualitative analyses. The overall quality evaluation score using telepresence observation showed no statistically significant difference from that obtained using in-person observation. In addition, the participants in this experiment showed a positive attitude toward the robot observation. However, we identified some weaknesses in current telepresence robots; for example, some observers were unable to observe instantaneous behaviors and the particularity of scenes. Telepresence robots should be improved to provide quick movement with high-quality video and sound for quality evaluation of kindergarten classrooms.
Mobility is fundamental for human beings. In the current society, many personal mobility solutions have been invented to enable more time-efficient mobility, such as self-balancing vehicles, electric unicycles, and electric scooters. Personal mobility devices can provide flexibility to transportation. However, most personal mobility devices need to be carried by their users in the case that they climb stairs and steps. Therefore, many researchers have focused on developing stair-climbing vehicles, but due to the complicated mechanism, these devices are usually huge and heavy. To realize a new type of personal mobility device with more flexibility, we proposed a novel concept of a personal mobility device design that combines the agile mobility of a wheel type mechanism but does not limit a human’s natural stair climbing ability. In this study, we introduced a compact personal mobility device, namely WeMo, under the concept of “wearing mobility”, which extends humans’ mobility in daily life. The developed hardware realizes “walking mode” and “driving mode”. Users can move with the motorized driven wheels of the device during driving mode, and users can walk on their feet without any interference from the device during walking mode. In this manuscript, the detailed design of the hardware and control strategy were explained first.Then, we conducted fundamental user tests and discussed the ability of the developed device from test results. Finally, the conclusions and future work were provided.
The inspection of oil storage tanks is a critical measure to prevent the risk of oil leakage. Therefore, research has focused on magnet-type climbing robots for automated tank inspections. While existing magnet-type climbing robots have demonstrated significant improvements in climbing steel structures, their capability in terms of metal thickness measurement has not been previously evaluated. During thickness inspections, ultrasonic thickness sensors require a probe to be pressed against target surfaces. To automate metal thickness measurements, this pressing motion of the probe needs to be performed by the robot. This study introduces a novel metal thickness measurement device comprising an ultrasonic probe, a linear actuator, a gel pump, and a pressure sensor designed for a magnet-type climbing robot. The linear actuator moves the probe to its initial position, the gel pump injects a coupling gel, and then the actuator moves the probe to the surface and back. Finally, our prototype of an ultrasonic probe with a linear actuator was installed on a magnet-type climbing robot to demonstrate its functionality in a practical application regarding an oil storage tank inspection system. The prototype achieved a measurement success rate of 65.9% and an average error of 0.7% compared to a reference thickness. This article details the design and development of the ultrasonic probe with a linear actuator to enable the probe to make contact with the surface. It then details the experimental results and evaluation of metal thickness measurement performed using the prototype and the climbing robot.