Oleg Korolkov

Mr. Oleg Korolkov

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
VSVladimir Stolyarov
Vladimir Stolyarov
OKOleg Korolkov
Oleg Korolkov
APAlexander PESIN
Alexander PESIN
GRGeorge Raab
George Raab
The problem of the real existence of the electroplastic effect during deformation of metallic materials of different nature is still relevant. At the same time, the influence of structure refinement is not considered enough. In this work, the deformation behavior of ultrafine-grained (UFG) titanium Grade 4 is compared with that of coarse-grained (CG) titanium under tension with pulse current of the low duty cycle. The deformation curves of both structure states are presented for different regimes of pulsed current and thermal heating from an external source. Structure studies by optical and scanning electron microscopy, as well as microhardness measurements have been carried out. It is shown that Grade 4 titanium under tension accompanied by pulsed current exhibits electroplastic effect (EPE) in the form of a flow stress reduction. EPE in UFG state is much stronger than in CG state. An increase in the density and duration of the current pulse leads to a multiple decrease in the flow stresses in CG and UFG titanium. The contribution in the flow stress reduction from heating by an external source was less than that from tension with pulse current at the same temperatures. The impact of pulsed current during tension does not influence microhardness and grain size.

31 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
Mikhail PakhomovMikhail Pakhomov
Mikhail Pakhomov
OKOleg Korolkov
Oleg Korolkov
MPMirko Pigato
Mirko Pigato
Claudio GennariClaudio Gennari
Claudio Gennari
Irene CalliariIrene Calliari
Irene Calliari
VSVladimir Stolyarov
Vladimir Stolyarov
The deformation behavior of duplex stainless steel under tension and bending, accompanied by a pulsed current and when heated by an external source, is investigated. The stress–strain curves are compared at the same temperatures. The contribution to the decrease in flow stresses is greater when using a multi-pulse current at the same temperature, compared to external heating. This confirms the presence of an electroplastic effect. An increase in the strain rate by an order of magnitude reduces the contribution of the electroplastic effect from single pulses to the reduction in flow stresses by 20%. An increase in the strain rate by an order of magnitude reduces the contribution of the electroplastic effect from single pulses to the reduction in flow stresses by 20%. However, in the case of a multi-pulse current, the strain rate effect is not observed. Introducing a multi-pulse current during bending reduces the bending strength by a factor of two and the springback angle to 6.5.

1 November 2021 in Journal of Machinery Manufacture and Reliability
Verified
Journal Article
Closed access
PDF file
OKOleg Korolkov
Oleg Korolkov
VSV. V. Stolyarov
V. V. Stolyarov
Tension and bending tests of commercially pure VT1-0 and Grade 4 titanium were carried out to assess the influence of the electroplastic effect on the stre

20 November 2001 in Proceedings of the Estonian Academy of Sciences. Engineering
Verified
Journal Article
Open access
OKOleg Korolkov
Oleg Korolkov
TRToomas Rang
Toomas Rang

6 May 2018 in KnE Materials Science
Verified
Journal Article
Open access
PDF file
OTO A Troickij
O A Troickij
OKOleg Korolkov
Oleg Korolkov
VSV I Stashenko
V I Stashenko
OSO B Skvorcov
O B Skvorcov
Electroplastic Processing of Titanium Implants

21 December 2024 in Journal of Machinery Manufacture and Reliability
Verified
Journal Article
Closed access
PDF file
OKOleg Korolkov
Oleg Korolkov
UUU. Kh. Ugurchiev
U. Kh. Ugurchiev
NNN. N. Novikova
N. N. Novikova
The modes of electroplastic deformation of the titanium alloy VT6 using three-point bending with subsequent application of the found modes for deformation of the implant blank are examined. The influence of the current density and the pulse duration at a constant duty cycle is estimated. To evaluate the electroplastic effect, the thermal contribution of the current was compared with heating from an external source.