Syngas, the product of biomass gasification, can play an important role in moving towards the production of renewable chemical commodities, by using acetogenic bacteria to ferment those gaseous mixtures. Due to the complex and changing nature of biomass, the composition and the impurities present in the final biomass-derived syngas will vary. Because of this, it is important to assess the impact of these factors on the fermentation outcome, in terms of yields, productivity, and product formation and ratio. In this study, Clostridium ljungdahlii was used in a fed-batch fermentation system to analyze the effect of three different biomass-derived syngases, and to compare them to equivalent, clean syngas mixtures. Additionally, four other clean syngas mixtures were used, and the effects on product ratio, productivity, yield, and growth were documented. All biomass-derived syngases were suitable to be used as substrates, without experiencing any complete inhibitory effects. From the obtained results, it is clear that the type of syngas, biomass-derived or clean, had the greatest impact on product formation ratios, with all biomass-derived syngases producing more ethanol, albeit with lesser total productivity.

A hydrothermal pre-treatment has been developed to improve sewage sludge quality or to produce low nitrogen biocrude via hydrothermal liquefaction (HTL) in a subsequent step. The mild hydrothermal pre-treatment (150 °C) step was performed with deionized water, sulfuric acid (0.5 M), or citric acid (0.5 M) to solubilize nitrogen containing compounds in the aqueous supernatant. Downstream, the residual solid material was liquefied with the addition of sodium carbonate via hydrothermal liquefaction (350 °C). The pre-treatment with citric acid transferred up to 66.7 wt. % of nitrogen into the aqueous supernatant, while 62.0 wt. % of carbon was recovered in the solid. Due to the pre-treatment lipids retained in the sewage sludge solid, which increased the favored biocrude yield up to 42.9 wt. % and the quality evaluating value H/C_eff ratio significantly to 1.48. Multi-method characterization of the resulted biocrude samples showed a lower concentration of N-heterocycles, while long-chain aliphatics and free fatty acid are increased.

Four nickel-based catalysts are synthesized by wet impregnation and evaluated for the hydrotreatment/hydrodeoxygenation of beech wood fast-pyrolysis bio-oil. Parameters such as elemental analysis, pH value, and water content, as well as the heating value of the upgraded bio-oils are considered for the evaluation of the catalysts’ activity and catalyst reuse in cycles of hydrodeoxygenation after regeneration. The reduction temperature, selectivity and hydrogen consumption are distinct among them, although all catalysts tested produce upgraded bio-oils with reduced oxygen concentration, lower water content and higher energy density. Ni/SiO₂, in particular, can remove more than 50% of the oxygen content and reduce the water content by more than 80%, with low coke and gas formation. The evaluation over four consecutive hydrotreatment reactions and catalyst regeneration shows a slightly reduced hydrodeoxygenation activity of Ni/SiO₂, mainly due to deactivation caused by sintering and adsorption of poisoning substances, such as sulfur. Following the fourth catalyst reuse, the upgraded bio-oil shows 43% less oxygen in comparison to the feedstock and properties comparable to the upgraded bio-oil obtained with the fresh catalyst. Hence, nickel-based catalysts are promising for improving hardwood fast-pyrolysis bio-oil properties, especially monometallic nickel catalysts supported on silica.

Organic solid wastes such as sewage sludge are potential feedstocks for the production of drop-in biofuels. Hydrothermal liquefaction (HTL) is a process that converts the wet sewage sludge into an organic biocrude. To fulfill industrial fuel standards, the considerable heteroatom content of the biocrude needs to be lowered by downstream processes. Nitrogen (N) contained in several compounds poses a challenge and yet, the complex chemical composition of HTL-biocrude samples has hindered detailed analysis and understanding. In particular, N-containing aromatic substances appear very persistent in biocrude. In the present work, two alkaline (NaHCO₃ and NaOH) and one acidic (HCL) aqueous solutions were subsequently applied to extract and recover polar N-containing compounds from the biocrude matrix with an N-content of 3.8 wt %. Gas chromatography-mass spectrometry, atmospheric pressure chemical ionization in positive mode, and Fourier transform ion cyclotron resonance mass spectrometry were applied for their characterization and results show that a large share of N-compounds with an aromatic, pyridinic structure was found in the acidic extracted fraction with an N-content of 9.5 wt %. Aliphatic N-compounds were less affected by the separation and ended in the residual fraction. N-compounds with multiple oxygen functionalizations are enriched in the alkaline extracted fractions. This showed that N-compounds with an aromatic structure are strongly affected by polar groups and can potentially be extracted by downstream processes with appropriate solvents.