In this paper, changes of microstructural characteristics of disperse systems during mechanical activation of zinc oxide (ZnO) have been investigated. ZnO powder was activated by grinding in a planetary ball mill in a continuous regime in air during 300 min at the basic disc rotation speed of 320 rpm and rotation speed of bowls of 400 rpm but with various balls-to-powder mass ratios. During ball milling in a planetary ball mill, initial ZnO powder suffered high-energy impacts. These impacts are very strong, and large amounts of microstructural and structural defects were introduced in the milled powders. The morphology and dispersivity of particles and agglomerates of all powders were investigated by scanning electron microscopy and scanning transmission electron microscopy. The specific surface area of initial ZnO powder was determined as 3.60 m(2) g(-1) and it increased to 4.42 m(2) g(-1) in mechanically activated powders. An increase of the ball-to-powder mass ratio led to a decrease of particle dimensions as well as increased the tendency for joining into quite compact agglomerates, that is aggregates, compared with the very loose, soft initial agglomerates. The obtained results pointed out that activation of ZnO powders produces a highly disperse, nano-scaled mixture of small particles, that is crystallites with sizes in the range of 10-40 nm. Most of these particles are in the form of aggregates with dimensions of 0.3-0.1 mum. The crystallite and aggregate size strongly depend on milling conditions, that is ball-to-powder mass ratio, as shown in this investigation.
Developing highly efficient semiconductor metal oxide (SMOX) sensors capable of accurate and fast responses to environmental humidity is still a challenging task. In addition to a not so pronounced sensitivity to relative humidity change, most of the SMOXs cannot meet the criteria of real-time humidity sensing due to their long response/recovery time. The way to tackle this problem is to control adsorption/desorption processes, i.e., water-vapor molecular dynamics, over the sensor’s active layer through the powder and pore morphology design. With this in mind, a KIT-5-mediated synthesis was used to achieve mesoporous tin (IV) oxide replica (SnO2-R) with controlled pore size and ordering through template inversion and compared with a sol-gel synthesized powder (SnO2-SG). Unlike SnO2-SG, SnO2-R possessed a high specific surface area and quite an open pore structure, similar to the KIT-5, as observed by TEM, BET and SWAXS analyses. According to TEM, SnO2-R consisted of fine-grained globular particles and some percent of exaggerated, grown twinned crystals. The distinctive morphology of the SnO2-R-based sensor, with its specific pore structure and an increased number of oxygen-related defects associated with the powder preparation process and detected at the sensor surface by XPS analysis, contributed to excellent humidity sensing performances at room temperature, comprised of a low hysteresis error (3.7%), sensitivity of 406.8 kΩ/RH% and swift response/recovery speed (4 s/6 s).
1 January 2020 in Processing and Application of Ceramics
The effects of strontium doping (0-2 mol%) on structure, microstructure and functional properties of potassium sodium niobate (KNN) thin films deposited on Pt(111)/TiOy/SiO2/Si substrates were investigated. Incorporation of Sr up to 1 mol% into the KNN crystal lattice hindered the grain growth, vertical roughness and contributed to the fine-grained and dense thin film microstructure with monoclinic crystal syngony. This effectively reduced leakage current and improved ferroelectric characteristics. Higher doping content (2 mol%) led to the formation of secondary phases and complete deterioration of functional properties. Stabilization of 1 mol% Sr-doped KNN solution with diethanolamine resulted in the film with dielectric constant and losses of 394 and 0.018 at 100 kHz, respectively, leakage current of 3.8 . 10(-8) A/cm(2) at 100 kV/cm and well saturated ferroelectric hysteresis with P-r of 6.8 mu C/cm(2) and low E-c of 85 kV/cm. Benefiting from improved leakage current characteristics at high electric fields and less defect structure, the film showed maximal local piezoelectric coefficient, d(33) similar to 110 pm/V determined by piezo-response force microscopy (PFM), ability to reach fully saturated local hysteresis under low switching DC voltage of 15 V and good ferroelectric domain mobility proven by successful in-situ poling of chosen area using PFM lithography.
1 January 2010 in Journal of the European Ceramic Society
Pure SnO2 nanofibers were synthesized via an electrospinning method and subsequently calcined at 550 °C to investigate the structure–property relationship governing H2S gas sensing performance. X-Ray diffraction confirmed the formation of the crystalline rutile-type SnO2. FE-SEM and TEM methods revealed a hierarchically porous morphology with fiber diameters ranging from 70 to 160 nm. BET measurements indicated a high specific surface area of 75 m2/g, consistent with the observed porous architecture. Gas sensing measurements toward H2S revealed a pronounced response value of 25 at 200 °C with the response time of 23 s, both superior to those recorded for acetone, ethanol, and hydrogen. The enhanced sensitivity and dynamic response are attributed to the large surface area and interconnected porous network of the nanofibers, which provide the abundant active sites and facilitate efficient gas diffusion.