We extracted magnesium-rich calcium phosphate bioceramics from tilapia bone using a gradient thermal treatment approach and investigated their chemical and physicochemical properties. X-ray diffraction showed that tilapia fish bone-derived hydroxyapatite (FHA) was generated through the first stage of thermal processing at 600–800 °C. Using FHA as a precursor, fish bone biphasic calcium phosphate (FBCP) was produced after the second stage of thermal processing at 900–1200 °C. The beta-tricalcium phosphate content in the FBCP increased with an increasing calcination temperature. The fact that the lattice spacing of the FHA and FBCP was smaller than that of commercial hydroxyapatite (CHA) suggests that Mg-substituted calcium phosphate was produced via the gradient thermal treatment. Both the FHA and FBCP contained considerable quantities of magnesium, with the FHA having a higher concentration. In addition, the FHA and FBCP, particularly the FBCP, degraded faster than the CHA. After one day of degradation, both the FHA and FBCP released Mg2+, with cumulative amounts of 4.38 mg/L and 0.58 mg/L, respectively. Furthermore, the FHA and FBCP demonstrated superior bone-like apatite formation; they are non-toxic and exhibit better osteoconductive activity than the CHA. In light of our findings, bioceramics originating from tilapia bone appear to be promising in biomedical applications such as fabricating tissue engineering scaffolds.
28 July 2023 in Journal of Vacuum Science & Technology A
The application of a diamondlike carbon (DLC) coating on rubber surfaces is a promising method to enhance the tribological properties of rubber and alleviate its poor wear resistance. However, in the preparation of DLC films, accurate pressure detection in the sputtering region is challenging due to the single detection position in common sputtering systems. In this paper, the direct current magnetic sputtering method was used to prepare DLC films on nitrile butadiene rubber (NBR). A set of Faraday beam detection device (FBDD) was employed to monitor the current density in the sputtering region. It was found that even if the pressure at the detection position of the vacuum gauge is consistent, the actual pressure in the sputtering region may be different under different rates of argon flow based on the detection results from the FBDD. The surface energy of DLC films was also calculated and researched. According to the results of FBDD, a series of analytical characterization methods were selected to explore the influence mechanism of changing the Ar flow rate on the properties of DLC films on NBR when the initial sputtering pressure remained consistent. The results of FBDD show that the density of the beam in the sputtering region increases with the increase in the Ar flow rate introduced into the vacuum chamber. The surface energy of DLC films was also calculated and evaluated by a contact angle tester. Raman and x-ray photoelectron spectroscopy results indicate that the increase in the Ar flow rate leads to an increase in pressure, which is conducive to the formation of sp3 in DLC films, and the increase in sp3 improves the surface energy of DLC films. The highest sp3 content and surface energy among as-prepared DLC films are observed when the argon flow rate was 40 SCCM. Ball-on disk friction experiment was used to characterize the tribological performance of DLC films on NBR rubber and the adhesion between DLC films and NBR rubber was evaluated by a nanoscratching test. Combining the results of tribology and nanoscratching testing, it can be inferred that the Ar flow rate plays an important role in improving the mechanical properties of DLC films on NBR rubber. Furthermore, the results of scanning electron microscopy confirmed that the sputtering atoms can effectively fill in the grooves of the rubber substrate. This finding is of significance for controlling the sputtering process of preparing DLC on rubber and improving the frictional properties of rubber.
The poor adhesion between the DLC film and rubber restricts its application of seals. Introducing a suitable interlayer can bolster the adhesion of the coating or film. In this study, nitrogen-doped diamond-like carbon (N-DLC) emerged as the optimal intermediate layer between rubber and DLC. A series of N-DLC/DLC multilayer films were fabricated via DC magnetron sputtering on nitrile rubber (NBR) substrates, varying the substrate bias voltage (0 V, 100 V, 200 V). A scanning electron microscopy analysis revealed that the composite film surface was smoother than the DLC film alone. The results of Raman spectroscopy and X-ray photoelectron spectroscopy indicated a robust bond between nitrogen and carbon atoms in the composite film, with nitrogen facilitating the conversion of sp3C-C bonds into sp2C=C. Mechanical tests demonstrated that the N-DLC interlayer improved film adhesion and reduced the CoF of the composite film to 0.2–0.3. Specifically, the CoF of the N-DLC/DLC film prepared at 100 V was as low as 0.20, with a wear amount of 1.13 mg. Consequently, the inclusion of the N-DLC interlayer substantially enhanced the mechanical and tribological properties of DLC-coated NBR, rendering this coating highly advantageous for various applications.