Gas sensors applied in real-time detection of toxic gas leakage, air pollution, and respiration patterns require a reliable test platform to evaluate their characteristics, such as sensitivity and detection limits. However, securing reliable characteristics of a gas sensor is difficult, owing to the structural difference between the gas sensor measurement platform and the difference in measurement methods. This study investigates the effect of measurement conditions and system configurations on the sensitivity of two-dimensional (2D) material-based gas sensors. Herein, we developed a testbed to evaluate the response characteristics of MoS2-based gas sensors under a NO2 gas flow, which allows variations in their system configurations. Additionally, we demonstrated that the distance between the gas inlet and the sensor and gas inlet orientation influences the sensor performance. As the distance to the 2D gas sensor surface decreased from 4 to 2 mm, the sensitivity of the sensor improved to 9.20%. Furthermore, when the gas inlet orientation was perpendicular to the gas sensor surface, the sensitivity of the sensor was the maximum (4.29%). To attain the optimum operating conditions of the MoS2-based gas sensor, the effects of measurement conditions, such as gas concentration and temperature, on the sensitivity of the gas sensor were investigated.
Implementing a heterostructure by vertically stacking two-dimensional semiconductors is necessary for responding to various requirements in the future of semiconductor technology. However, the chemical-vapor deposition method, which is an existing two-dimensional (2D) material-processing method, inevitably causes heat damage to surrounding materials essential for functionality because of its high synthesis temperature. Therefore, the heterojunction of a 2D material that directly synthesized MoS2 on graphene using a laser-based photothermal reaction at room temperature was studied. The key to the photothermal-reaction mechanism is the difference in the photothermal absorption coefficients of the materials. The device in which graphene and MoS2 were vertically stacked using a laser-based photothermal reaction demonstrated its potential application as a photodetector that responds to light and its stability against cycling. The laser-based photothermal-reaction method for 2D materials will be further applied to various fields, such as transparent display electrodes, photodetectors, and solar cells, in the future.
21 May 2025 in IEEE Transactions on Semiconductor Manufacturing
In this study, the periodic purge process of the silicon nitride oxide deposition chamber was quantitatively analyzed and optimized using a real-time contaminant particle sensor (RTCPS). The RTCPS can measure the particle number concentration emitted from the semiconductor process chamber at the foreline in real time. The previous periodic purge process, which used a cycle purge method alternating between showerhead flow on and off, only expelled the accumulated particles in the chamber during the early stages of each cycle. On the other hand, by adding heater movement during the cycle, continuous particle emission was achieved throughout the periodic purge, resulting in improved efficiency. Additionally, the purge time was reduced, leading to increased productivity.
Wafer-type temperature sensors are widely used during semiconductor fabrication as integrated monitoring sensors for the real-time monitoring of wafer surface temperature, which affects the quality and yield of semiconductor devices. In recent years, various wafer-type temperature sensors have been developed according to the process type and temperature range for monitoring the temperature distribution. However, there is little research on the calibration system to ensure the accuracy and reliability of the developed wafer-type temperature sensor. In this study, we designed a system for the calibration of wafer-type temperature sensors. With this system, the traceability of the sensor can be guaranteed by calibrating the sensing characteristics, such as area uniformity, temperature stability, and accuracy. The conventional temperature calibration bath is calibrated by placing a wafer-type temperature sensor in a liquid-controlled system to have uniform temperature. This method is difficult to apply to the field because the wafer-type temperature sensor can be contaminated by liquids and can adversely affect semiconductor processes. For this reason, we used a heating chamber similar to chemical vapor deposition equipment for a calibration system. We evaluated the properties of the calibration system including the rising time (which means the time taken to reach the target temperature) and temperature stability according to the heat capacity. Moreover, we developed a measurement method that allows for the evaluation of the temperature of the wafer-type temperature sensor within 15 min at 150 °C. The calibration system and measurement method developed in this study are expected to improve the efficiency of semiconductor fabrication processes.
Given the increasing demand for sustainable energy and self‐powered devices, energy‐harvesting technologies, such as triboelectric nanogenerators (TENGs), are drawing attention. To address the short charge retention in conventional polymer materials, 2D materials with high surface areas and intrinsic charge‐trapping capabilities, such as MoS 2 , are being utilized as friction layers in TENGs. However, their power generation is too low for practical applications owing to their atomically thin nature, limiting their use as fillers in polymer‐based systems. We report a 2D‐material‐based high‐power TENG using 3D hierarchical MoS 2 (3DH‐MoS 2 ) as a primary friction material. The 3DH‐MoS 2 is synthesized via low‐temperature metal–organic chemical vapor deposition, enabling the direct growth of a uniform, large‐area, 3D‐nanostructured friction layer on a polymer substrate without additional processes. This 3D nanostructure increases the amount of charge‐trapping sites and significantly enhances the durability of the device. The 4 × 4 cm 2 3DH‐MoS 2 ‐based TENG produces a maximum output voltage of 320.1 V and a power density of 0.841 mW cm −2 , proving it can effectively power light‐emitting diodes and a calculator, maintaining its performance over 10 000 cycles. In addition, the device can generate electricity from gas and water flow and human motion, highlighting the potential and versatility of 2D‐material‐based energy‐harvesting systems.
Humidity degrades the output of triboelectric nanogenerators (TENGs) by anything from a few tens of percent to more than two orders of magnitude, and no single material property accounts for that spread. We present an analytical framework for polymer contact-separation TENGs in which the relative humidity reaches the device output through two measurable material descriptors. We obtain the effective permittivity from a three-phase Bruggeman relation that splits sorbed water into a rotationally hindered bound population and a free one, so that the polymers taking up the most water are those in which most of it is dielectrically inactive. We then treat moisture as removing charge that has already separated rather than preventing its separation, and place that removal at contact, where a mobile water film on either facing surface short-circuits the two charged faces. How much charge is lost depends on whether the wetted regions connect: isolated patches that drain only their own footprint and a spanning film the whole contact. The wetted area belongs to the two faces together, so the threshold is a property of the pair, and only free multilayer water can bridge a contact, which holds the loss down through the drier half of the range. Applying the descriptors to sixteen polymer pairs, we find that the retention of open-circuit voltage between 10 % and 90 % RH spans 0.7 to 65 %, and that the ranking of the pairs inverts between dry and humid operation. Measurements on five pairs place the half-points at 56 to 75 % RH, against 57 to 77 % predicted.