This article presents a methodology to design a circuit to compensate for process skew by exploiting an inherent dimension-dependent effect of process skew on change in the threshold voltage. We design a voltage reference circuit with a hybrid architecture of bandgap reference (BGR) and CMOS reference, which generates a nominal voltage level of (bandgap - threshold). By compensating the process skew of the threshold term with the proposed dimension-induced effect as well as the temperature dependence, the circuit achieves the simultaneous benefits of BGR and CMOS references. For verification, the circuit was fabricated in three wafers of a 0.18-μm CMOS including extreme slow and fast corners. With an active area of 0.0045 mm², it consumes 192 pW at room temperature. Measurement from 45 chips (15 chips per wafer) shows untrimmed process/voltage/temperature variations of 0.53%, 0.020%/V, and 33 ppm/°C, respectively.
20 July 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper presents a temperature sensor that combines a leakage-based bandgap-Vth reference and an asynchronous SAR. The proposed sensor is implemented with 0.18 μm CMOS technology. By sampling leakage-based biases directly in the SAR ADC, the sensor consumes 490 pW at 20 ∘C with a conversion time of 200 ms and stably works with a 1-point calibration, showing a ±2.35 oC peak-to-peak inaccuracy from -10 to 100 ∘C. The proposed sensor can operate across a wide range of supply voltage of 1 V to 2.1 V, with a supply sensitivity of 1.073 ∘C/V.
2 August 2018 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This paper presents detailed analyses on leakage-based bandgap reference (BGR) circuit for ultralow-power applications. Design considerations for power supply rejection ratio and noise characteristics are provided with pole/zero analysis. Startup settling issue is also discussed with measurements. For verification, a test BGR circuit is implemented in a 0.18- $\mu \text{m}$ CMOS technology. The standard deviation of proportional-to-absolute-temperature (PTAT) voltages measured from 20 chips is 1.15% at 30 °C. The BGR also uses two PTAT voltages to reduce the resistance for complementary-to-absolute-temperature generation, hence alleviating the tradeoff limitation between power consumption and area cost. With an active area of 0.056 mm 2 , the BGR consumes 19 nW at room temperature. Measurements from 20 chips show a standard deviation of 0.54% at 30 °C without any trimming, a temperature dependence of 143 ppm/°C and a line regulation of 2.4%/V.
5 April 2022 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This brief proposes a resistor-less bandgap reference (BGR) based on a leakage-based proportional-to-absolute-temperature (PTAT) scheme. The effect of process variations on the current is mitigated by employing self-biased current-limiting MOS transistors. The bias voltages needed for approximating a large resistance can be obtained from a single branch by placing threshold-sampling transistors on top of the BGR output. The fabricated BGR in 0.18- $\mu \text{m}$ CMOS occupies an active area of 0.035 mm 2 and consumes 20.5 nW, and it shows a standard deviation of 0.68% at untrimmed reference voltages.
This paper presents an ultra-low-power CMOS voltage reference designed and verified in an 180 nm standard CMOS technology. To achieve DC and AC supply sensitivity under 0.01%/V and −100 dB, it employs a single transistor and two 2-T cores to improve supply immunity with minimal overhead, adding only one drain-to-source voltage for the total supply voltage. The proposed design achieves a line sensitivity of 0.0027%/V in a supply voltage range of 0.5 V to 2 V and consumes 630 pW with a supply voltage of 0.5 V. The simulated temperature coefficient is 12 ppm/°C in a temperature range of −40 °C to 150 °C, and the simulated power supply rejection ratio is −100.5 dB at 100 Hz without requiring any output decoupling capacitor.
19 November 2025 in IEEE Open Journal of the Solid-State Circuits Society
The rapid growth of power-constrained applications, including the Internet of Things (IoT) and wearables, demands sensor interfaces with high accuracy and reliability. A fundamental design challenge arises as their performance is severely limited by thermal drift within the analog front-end (AFE) and analog-to-digital converter (ADC) circuits. To address this, this article reviews two principal strategies: 1) the development of robust voltage and frequency reference circuits and 2) the implementation of on-chip temperature calibration. The review covers state-of-the-art temperature-compensated voltage references, such as subthreshold and BJT/MOS hybrid architectures, as well as stable frequency references based on LC and RC time constants. Furthermore, it examines advanced sensor interfaces that integrate on-chip temperature sensors for real-time error correction, featuring recent case studies on current sensor designs. These comprehensive advances are crucial for enabling reliable, energy-efficient sensor interfaces intended for precision-critical applications.