The well productivity of high-waxy reservoirs is highly influenced by temperature changes. A decrease in temperature can cause the precipitation of wax from the crude oil, leading to a decrease in the formation’s drainage capacity and a drop in oil production. In this study, the wax precipitation of crude oil is characterized by rheological properties tests and differential scanning calorimetry (DSC) thermal analysis. The wax damage characteristics of cores and the relative permeability curves at different temperatures were investigated through coreflood experiments. Furthermore, nanoemulsion is selected as a chemical agent for injection fluid. The nuclear magnetic resonance (NMR) scanning technique is used to investigate the effects of oil recovery enhancement at different pores by increasing temperature and adding nanoemulsion. By comparing the changes in T₂ spectra and the distribution pattern of residual oil before and after liquid injection, the results have shown that both increasing temperature and adding nanoemulsion have a significant effect on oil recovery. The improvement of micropores is less pronounced compared to macropores. The produced oil mainly comes from the large pores. When the temperature is lower than the crude oil dewaxing point temperature, there is a serious dewaxing plugging phenomenon in the pores. Additionally, by observing the pattern of residual oil distribution at the end of the NMR online drive, it is hereby classified into wax deposition retention type, weak water washing retention type, and immobilized type, each with its own distinct characteristics. Wettability alteration and interfacial tension reduction can help to improve the drainage capacity of high-wax oil reservoirs, which is the main mechanism of nanoemulsion for enhanced oil recovery. These findings are highly valuable for enhancing the comprehension of the impact of highly waxed crude oils on drainage capacity and the ultimate oil recovery rate, particularly in relation to wax precipitation deposition.

At present, the imbibition behavior in tight rocks has been attracted increasing attention since spontaneous imbibition plays an important role in unconventional oil and gas development, such as increasing swept area and enhancing recovery rate. However, it is difficult to describe the imbibition behavior through imbibition experiment using tight rock core. To characterize the imbibition behavior, imbibition and drainage experiments were conducted among water, oil, and gas phases in a visible circular capillary tube. The whole imbibition process is monitored using a microfluidic platform equipped with a high frame rate camera. This study conducts two main imbibition experiments, namely liquid-displacing-air and water-displacing-oil experiments. The latter is a spontaneous imbibition that the lower-viscosity liquid displaces the higher-viscosity liquid. For the latter, the tendency of imbibition rate with time does not match with previous model. The experimental results indicate that it is unreasonable to take no account of the effect of accumulated liquid flowing out of the capillary tube on imbibition, especially in the imbibition experiments where the lower-viscosity liquid displaces the higher-viscosity liquid. A mathematical model is established by introducing an additional force to describe the imbibition behavior in capillary tube, and the model shows a good prediction effect on the tendency of imbibition rate with time. This study discovers and analyzes the effect of additional force on imbibition, and the analysis has significances to understand the imbibition behavior in tight rocks.

The stability of nitrogen gas foam hinders its applicability in petroleum applications. Fly ash nanoparticles and clay improve the N₂ foam stability, and flue gas foams provide a cost-effective solution for carbon capture, utilization, and storage (CCUS). This study examines the stability, volume, and bubble structure of foams formed using two anionic surfactants, sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (SDBS), along with the cationic surfactant cetyltrimethylammonium bromide (CTAB), selected for their comparable interfacial tension properties. Analysis of foam stability and volume and bubble structure was conducted under different CO₂/N₂ mixtures, with half-life and initial foam volume serving as the evaluation criteria. The impact of fly ash and clay on SDS-N₂ foam was also evaluated. The results showed that foams created with CTAB, SDBS, and SDS exhibit the greatest stability in pure nitrogen, attributed to low solubility in water and limited gas diffusion. SDS showed the highest foam strength attributable to its comparatively low surface tension. The addition of fly ash and clay significantly improved foam stability by migrating to the gas–liquid interface, creating a protective barrier that reduced drainage. Both nano fly ash and clay improved the half-life of nitrogen foam by 11.25 times and increased the foam volume, with optimal concentrations identified as 5.0 wt% for fly ash and 3.0 wt% for clay. This research emphasizes the importance of fly ash nanoparticles in stabilizing foams, therefore optimizing a foam system for enhanced oil recovery (EOR).