Ahmad Zubair Sultan

Dr. Ahmad Zubair Sultan

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2015 in Procedia Manufacturing
Verified
Journal Article
Open access
ASAhmad Zubair Sultan
Ahmad Zubair Sultan
SSSafian Sharif
Safian Sharif
Denni KurniawanDenni Kurniawan
Denni Kurniawan
This paper focuses on the effect of drilling parameters on tool wear and hole quality in terms of diameter error, roundness, cylindricity, and surface roughness. In this work, the drilling was conducted using uncoated carbide tool with diameter of 4 ± 0.01mm with point angle of 135° and helix angle of 30°. The drilling was done at different levels of spindle speed (18 and 30 mmin-1) and feed rate (0.03, 0.045 and 0.06 mmrev-1). Austenitic stainless steel AISI 316L was the workpiece material. Comparatives analysis was done on hole diameter, roundness, cylindricity, and surface roughness of the drilled holes by experimentation. From the result, the hole quality characteristics are mostly influenced by cutting speed and feed rate. An exception was for circularity error where a two tail t-test for circularity error indicates that cutting speed and feed rate give no significant influence on circularity error. As the cutting speed increases, the surface roughness decreases (1.09μm). Contrary, when the feed rate increases, the surface roughness value increases as well. For cylindricity error, lower cutting speed and lower feed rate will give better result. In terms of diameter error, feed rate influences more than cutting speed. Minimum diameter error was achieved when low cutting speed and low feed rate were employed

1 January 2015 in Procedia Manufacturing
Verified
Journal Article
Open access
ASAhmad Zubair Sultan
Ahmad Zubair Sultan
SSSafian Sharif
Safian Sharif
Denni KurniawanDenni Kurniawan
Denni Kurniawan
Knowledge on the chip formation mechanism during drilling is very important to deliver the chips with size and shape as expected. Long chips cannot rid smoothly over drill flutes hence should be avoided while small chips can be removed easily from the machined hole. In this study, performance of a solid carbide twist drill through drilling of AISI 316L stainless steels was evaluated in terms of chip formation. This study aims to better define and further characterize the different chips shape and dimensions as a function of tool wear and cutting conditions in drilling the stainless steel. Experiments conducted on various combinations of cutting speed (18 and 30 m min-1) and feed rate (0.03, 0.045 and 0.06mm rev-1) to present the differences in chip formation. Optical observation and comparative analysis of flank wear of the twist drill were done. As the results of the performed experiments, the lowest cutting speed-lowest feed rate reveals better performance due to desirable chips formation on austenitic stainless steels drilling

1 January 2019 in Procedia Manufacturing
Verified
Journal Article
Open access
ASAhmad Zubair Sultan
Ahmad Zubair Sultan
SSSafian Sharif
Safian Sharif
FNFethma M. Nor
Fethma M. Nor
Denni KurniawanDenni Kurniawan
Denni Kurniawan


4 December 2013 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
ASAhmad Zubair Sultan
Ahmad Zubair Sultan
SSS. Sharif
S. Sharif
Denni KurniawanDenni Kurniawan
Denni Kurniawan
Increased attention on environmental and health impacts by industrial activities forces the manufacturing industry to reduce the mineral oil-based metalworking fluids as a cutting fluid. The advantages of using vegetable oil-based cutting fluids on tool wear and the cutting force have been reported in the literature, but those reporting the effects of their use on the surface finish of the workpiece are still lacking. This mini-review gives an overview of the influence of vegetable oil-based cutting fluids on surface integrity of steel during drilling process. Effect of the different cooling strategies on surface integrity is also presented.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
APAgung Tri Pamungkas
Agung Tri Pamungkas
AMAbdul Kadir Muhammad
Abdul Kadir Muhammad
ASAhmad Zubair Sultan
Ahmad Zubair Sultan
AAArman Arman
Arman Arman
This study aims to design an Internet of Things – based monitoring system to meet safety requirements for humans and the environment and to perform simulations This study aims to design an Internet of Things – based monitoring system to meet safety requirements for humans and the environment and to perform simulations