In this work, the effect of different mixing techniques on thermal and mechanical properties of graphene nanoplatelets (GNPs) and graphene nanofibers (GANFs) loaded epoxy nanocomposites was investigated. Three dispersion methods were employed: a high shear rate (HSR), ultrasonication (US) and the fluidized bed method (FBM). The optical microscopy has revealed that the most suitable dispersion, in terms of homogeneity and cluster size, is achieved by implementing the US and FBM techniques, leading to nanocomposites with the largest increase of glass transition temperature, as supported by the DMA analysis data. The fracture toughness results show a general increase of both the critical stress intensity factor (KIC) and the critical strain energy release rate (GIC), likely due to the homogeneity and the low scale dispersion of the carbonaceous nanostructures. Based on the nanocomposite fracture toughness improvements and also assuming a potential large scale up production of the nanocomposite matrix, a single mixing technique, namely the FBM, was employed to manufacture the carbon fiber reinforced composite (CFRC). This method has resulted in being less time-consuming and is potentially most suitable for the high volume industrial production. The CFRCs were characterized in terms of tensile, flexural and interlaminar fracture toughness properties and the results were analyzed and discussed.
InconelTM 718 is widely used for commercial application in aerospace industry and additive manufacturing process allows for versatile design and manufacturing opportunities. In the present research, the results of a wide experimental campaign run on additive manufactured InconelTM 718 specimens obtained with different processing parameters are presented. In particular, the influence of process parameters (for both vertical and horizontal planes with respect to the building direction) on the hardness properties are investigated. A further investigation is performed on the optimal hardness testing procedure for additive manufacturing. The research is extended to as-built and heat-treated specimens. The new insight gained is that the orientation of the printing direction with respect to indentation direction can be responsible for scattering in hardness measurements and indentation size effect. As-built specimens show a strong anisotropy for in-plane and growth directions and an increment of hardness with respect to increasing energy density. The difference between hardness value with respect to the energy density and the measurements scattering are reduced by the heat treatment. A careful handling of hardness data is required when dealing with additive manufactured materials.
Metal foams are a relatively new class of materials with many interesting combinations of physical and mechanical properties. Among them, the closed-cells aluminum foams are the most interesting for structural applications in the aerospace industry. There exist different methods to produce metal foams. An innovative manufacturing technique was developed in this study, proving the possibility to produce closed-cells aluminum foams through the cold spray additive manufacturing technology (CS). In particular, two different sets of samples were produced by varying the cold spray process parameters aiming at: i) studying the advantages and the issues of cold spray for manufacturing precursors for metal foams; ii) analyzing the correlation among the CS printing strategy and parameters, the foaming process and the physical and the morphological characteristics of the resulting foams; iii) finally, finding appropriate conditions to form closed-cells aluminum foams via CS.
NUSES is a planned space mission aiming to test new observational and technological approaches related to the study of low-energy cosmic rays, gamma rays, and high-energy astrophysical neutrinos. Two scientific payloads will be hosted onboard the NUSES space mission: Terzina and Zirè. Terzina will be an optical telescope readout by SiPM arrays for the detection and study of Cerenkov light emitted by Extensive Air Showers (EASs) generated by high-energy cosmic rays and neutrinos in the atmosphere. Zirè will focus on the detection of protons and electrons up to a few hundred MeV and 0.1–30 MeV photons and will include the Low-Energy Module (LEM). The LEM will be a particle spectrometer devoted to the observation of fluxes of low-energy electrons in the 0.1–7-MeV range and protons in the 3–50 MeV range in low Earth orbit (LEO) followed by the hosting platform. The detection of Particle Bursts (PBs) in this physics channel of interest could provide insights into understanding complex phenomena such as possible correlations between seismic events or volcanic activity with the collective motion of particles in the plasma populating Van Allen belts. With its compact size and limited acceptance, the LEM will allow the exploration of hostile environments such as the South Atlantic Anomaly (SAA) and the inner Van Allen belt, in which the anticipated electron fluxes are on the order of to electrons per square centimeter per steradian per second. Concerning the vast literature on space-based particle spectrometers, the innovative aspect of the LEM resides in its compactness, within cm3, and in its “active collimation” approach to dealing with the problem of multiple scattering at these low energies. In this work, the geometry of the detector, its detection concept, its operation modes, and the hardware adopted will be presented. Some preliminary results from a Monte Carlo simulation (Geant4) will be shown.