By the term, lattice structures are intended topologically ordered open-celled structures consisting of one or more repeating unit cells. Technological development and especially the growth of the additive manufacturing (AM) industry allows innovative structural design, including complex lattice structure. Selective laser melting (SLM) is an AM process that enables the manufacture of space filling structures. This work investigated the influence of the most important process parameter settings on lattices printability, focusing on the geometrical accuracy, the quantity of powders adhered to the main frame (satellites) and their compression behaviour. The process parameters such as the laser power, scan speed and layer height affect vigorously the design, quality and mechanical properties of the part. The aim of the paper is to evaluate how different parameter combinations affect the cellular structures’ printing. Twenty-four lattice structures with cubic and rhombic dodecahedron unit cells made of stainless steel 17-4PH (AISI-630) were printed using different combinations of SLM process parameters. Each structure was analysed considering its geometrical, topological and mechanical properties. Finally, the best parameter combination was evaluated comparing results achieved. Although this work investigated the 17-4PH stainless steel, physical principles related to the printing process described are generally true for the SLM process. Therefore, the adopted approach could still be suitable also for all the other materials commonly used with this AM technology.

As a result of the increasing environmental awareness, the concern for environmental sustainability and the growing global waste problem, the interest of bio-composites materials is growing rapidly in the last years in order to use them in various engineering fields. Tremendous advantages and opportunities are associated with the use of these materials. On the other hand, some issues are related to the superficial properties of the bio-laminates, in particular the wear properties, the flame resistance and the aesthetic appearance have to be improved in order to extend the application fields of these materials. Aiming to these goals this paper deals with the study of the deposition of aluminum coating through cold spray process on hemp/PLA bio-composites manufactured by using the compression molding technique. Therefore, SEM observations, roughness analyses, bending tests, pin on disk and scratch tests were carried out in order to study the feasibility of the process and to investigate on the properties of the coated samples. The experimental results proved that when the process parameters of the deposition process are properly set, no damages are induced in the composite panel and that the aluminum coating, under specific load conditions, resulted to be able to protect the substrate.

Inconel^TM 718 is widely used for commercial application in aerospace industry and additive manufacturing process allows for versatile design and manufacturing opportunities. In the present research, the results of a wide experimental campaign run on additive manufactured Inconel^TM 718 specimens obtained with different processing parameters are presented. In particular, the influence of process parameters (for both vertical and horizontal planes with respect to the building direction) on the hardness properties are investigated. A further investigation is performed on the optimal hardness testing procedure for additive manufacturing. The research is extended to as-built and heat-treated specimens. The new insight gained is that the orientation of the printing direction with respect to indentation direction can be responsible for scattering in hardness measurements and indentation size effect. As-built specimens show a strong anisotropy for in-plane and growth directions and an increment of hardness with respect to increasing energy density. The difference between hardness value with respect to the energy density and the measurements scattering are reduced by the heat treatment. A careful handling of hardness data is required when dealing with additive manufactured materials.

Metallization of Vitrimers by cold spray: A preliminary study VISCUSI Antonio, PERNA Alessia Serena, MARTONE Alfonso, PALMIERI Barbara, CILENTO Fabrizia, AM

Metal foams are a relatively new class of materials with many interesting combinations of physical and mechanical properties. Among them, the closed-cells aluminum foams are the most interesting for structural applications in the aerospace industry. There exist different methods to produce metal foams. An innovative manufacturing technique was developed in this study, proving the possibility to produce closed-cells aluminum foams through the cold spray additive manufacturing technology (CS). In particular, two different sets of samples were produced by varying the cold spray process parameters aiming at: i) studying the advantages and the issues of cold spray for manufacturing precursors for metal foams; ii) analyzing the correlation among the CS printing strategy and parameters, the foaming process and the physical and the morphological characteristics of the resulting foams; iii) finally, finding appropriate conditions to form closed-cells aluminum foams via CS.