Viktoriia Shtefan

Prof. Dr. Viktoriia Shtefan

Department of Technical Electrochemistry, National Technical University Kharkiv Polytechnic Institute, Kharkiv, Kharkivs’ka Oblast’, Ukraine
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2015 in Russian Journal of Electrochemistry
Verified
Journal Article
Closed access
PDF file
Viktoriia ShtefanViktoriia Shtefan
Viktoriia Shtefan
ASA. Yu. Smirnova
A. Yu. Smirnova

26 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
JZJosephine Zeisig
Josephine Zeisig
Viktoriia ShtefanViktoriia Shtefan
Viktoriia Shtefan
LGLars Giebeler
Lars Giebeler
UKUta Kühn
Uta Kühn
GAGebert Annett
Gebert Annett
JHJulia Kristin Hufenbach
Julia Kristin Hufenbach
In this study, a newly developed high-strength cast Fe81Cr15V3C1 (wt%) steel with a high resistance against dry abrasion and chloride-induced pitting corrosion is presented. The alloy was synthesized through a special casting process that yielded high solidification rates. The resulting fine, multiphase microstructure is composed of martensite, retained austenite and a network of complex carbides. This led to a very high compressive strength (>3800 MPa) and tensile strength (>1200 MPa) in the as-cast state. Furthermore, a significantly higher abrasive wear resistance in comparison to the conventional X90CrMoV18 tool steel was determined for the novel alloy under very harsh wear conditions (SiC, α-Al2O3). Regarding the tooling application, corrosion tests were conducted in a 3.5 wt.% NaCl solution. Potentiodynamic polarization curves demonstrated a similar behavior during the long-term testing of Fe81Cr15V3C1 and the X90CrMoV18 reference tool steel, though both steels revealed a different nature of corrosion degradation. The novel steel is less susceptible to local degradation, especially pitting, due to the formation of several phases that led to the development of a less dangerous form of destruction: galvanic corrosion. In conclusion, this novel cast steel offers a cost- and resource-efficient alternative to conventionally wrought cold-work steels, which are usually required for high-performance tools under highly abrasive as well as corrosive conditions.

1 January 2019 in Materials Today: Proceedings
Verified
Journal Article
Closed access
Viktoriia ShtefanViktoriia Shtefan
Viktoriia Shtefan
NKN. Kanunnikova
N. Kanunnikova
APA. Pilipenko
A. Pilipenko
HPH. Pancheva
H. Pancheva

1 March 2020 in Protection of Metals and Physical Chemistry of Surfaces
Verified
Journal Article
Closed access
PDF file
Viktoriia ShtefanViktoriia Shtefan
Viktoriia Shtefan
NKN. A. Kanunnikova
N. A. Kanunnikova
The present work was devoted to a study of the effect of the electrolyte composition on the anodic behavior of stainless steel. Morphology and X-ray phase composition of oxide coatings formed in Al- and Ti-containing electrolytes have been investigated. Electrical conductivity and defects of the coatings have been studied by the method of impedance spectroscopy. It has been established that the introduction of aluminum or titanium oxides into the coating composition reduces the corrosion rate of steel in chloride media.

9 February 2024 in Journal of Materials Science & Technology
Verified
Journal Article
Open access
XHXiaoliang Han
Xiaoliang Han
IKIvan Kaban
Ivan Kaban
JOJiri Orava
Jiri Orava
SDSaurabh Mohan Das
Saurabh Mohan Das
Viktoriia ShtefanViktoriia Shtefan
Viktoriia Shtefan
MHMichael Herbig
Michael Herbig

1 December 2013 in Russian Journal of Applied Chemistry
Verified
Journal Article
Closed access
PDF file
Viktoriia ShtefanViktoriia Shtefan
Viktoriia Shtefan
ASA. Yu. Smirnova
A. Yu. Smirnova
Possibility and conditions of obtaining cerium-containing oxide coatings on titanium alloys by microarc oxidation in electrolytes with tartrate and citrate cerium complexes were determined. The effect of organic cerium complexes on the kinetic parameters of the microarc oxidation of titanium alloys was studied. Porous oxides coatings containing up to 20% cerium were obtained.