This work aims to evaluate the quality of drinking water in the Disi aquifer in Jordan. Several water quality parameters are included in the mathematical equation to evaluate the average water quality and establish the suitability of water for drinking purposes. Water sampling zones from three wells were used to calculate the water quality indices (WQI). The water samples were analyzed for several physicochemical parameters, including pH, turbidity, total dissolved solids, Na⁺, Ca²⁺, Mg²⁺, Na⁺, K⁺, HCO³⁻, SO₄²⁻, Cl⁻, NO₃⁻, total hardness, electrical conductivity (EC) and other elements (Fe²⁺, Zn²⁺, Mn²⁺, Cd²⁺, As²⁻, Pb⁴⁺ and Cu²⁺), in the groundwater wells. Biological parameters, such as faecal coliform, were also tested. The Weighted Arithmetic WQI indicated that most of the wells were of good to excellent quality. These determined indices support decision making and are beneficial to monitoring the groundwater quality in the Disi aquifer. The relative weight is specific to each parameter and ranges from 1 to 5; it establishes the importance of the water quality parameters for domestic purposes. The WQI analysis rates the water quality between 75 to 65 from good to medium. The water quality of the Disi aquifer for potable drinking water was compared with the guidelines of the World Health Organization (2011) and the Jordan Drinking Standard (JS286); the results indicated that water in the Disi aquifer was of high quality and was fit for drinking.

The acidizing approach belongs to the well workover operations, where acid mixtures are initially implemented to treat damage near the wellbore area after drilling operations have been completed. Acidizing treatment is characterized by removal of fine particles and debris from the porous media of the damaged zone, hence leading to improve oil production from wells. This study evaluates the assessment of the acidizing treatment in vertical oil-producing wells. Gradually, the damage formation was reduced and then eliminated, and to a great extent, was compensated with the better performance of oil production from reservoirs. Target candidate wells were enriched by environmentally friendly additives and special chemicals, in predefined amounts, to achieve enhanced oil production rates from wells. A semi-analytical model was formulated for extrapolating the skin magnitude, depending on the damage formation’s permeability parameter as well as on the physical characteristics and reservoir depth. The figures of skin magnitude for all target wells were decreased, and oil production rates were enhanced after performing the matrix acidizing process. These findings are valid for diverse geological settings of different formations, as all treated intervals within the investigated wells have shown an objective response to the matrix acidizing approach. Eventually, productivity rates are imperative to increase potential economic outcomes.

Drilling optimization is very important during drilling operation, to save time and reduce cost of operation thus increases the profit. Drilling optimization aims to optimize controllable variables during drilling operation such as weight on bit and bit rotation speed for obtaining maximum drilling rate. In this study had been selected the effects of several parameters during drilling operation. Important parameters such as depth, density, bit weight, rotary speed per minute, efficiently cuttings transported hole is to take into account the factors given in Table 3. It was concluded that average annular fluid velocity is between 414.17 to 581.24ft/min, dominating parameter on cuttings transport, the higher the flow rate. s Another important factor is the mainly the rheological properties of the drilling fluid such as Vis=45-50 s, p.v=12, PH=10, mud weight is between 8.57 ppg to 8.74 ppg. The rate of penetration for the field data had been calculated for several data points. Although the weight on bit has increase from 6600 until 19800 lbs, 1137.41 lbs/in, rate of penetration still in the range of 11.74 ft/hr. The optimized bit weight is 13200 lbs or 1077.55 lbs/in during drilling operation, penetration rate for depth 4330.02 ft is suitable due to formation that is may be high in strength.

This paper was conducted to delimit the water influx in the Hamzeh oil reservoir, located in northeastern Jordan approximately 150 km east of Amman. Petroleum reservoirs are frequently encompassed by water aquifers that back up the reservoir pressure through water inflow. When the pressure declines in a petroleum reservoir, the water aquifer responds by providing an influx of water. Gradually, the damage is reduced and then eliminated, and more oil is produced from the reservoir. The material balance equation (MBE) is used as the fundamental method for this study, predicting reservoir performance for a period of 11 years. The results for this study prove that the reservoir has a water drive mechanism and that the original oil in place (OOIP) was 24,958,290 m³. The projected oil recovery factor ranges from 10.9 to 25 percent for the Hummar and Shueib formations, respectively, depending on the areal efficiency assumed in the calculations. The water influx for the 11-year period was predicted by an MBE, an unsteady-state model, and the results of the performance reservoir.