Gianluca Foti

Dr. Gianluca Foti

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2023 in Energies
Verified
Journal Article
Open access
PDF file
ABAlessio Bosio
Alessio Bosio
GFGianluca Foti
Gianluca Foti
SPStefano Pasini
Stefano Pasini
DSDonato Spoltore
Donato Spoltore
There has been a recent surge in interest toward thin film-based solar cells, specifically new absorber materials composed by Earth-abundant and non-toxic elements. Among these materials, antimony selenide (Sb2Se3) is a good candidate due to its peculiar properties, such as an appropriate bandgap that promises a theoretical maximum power conversion efficiency of 33% and an absorption coefficient of around 105 cm−1, enabling its use as a thin film absorber layer. However, charge carrier transport has been revealed to be problematic due to its cumbersome structure and the lack of a doping strategy. In this work, we aim to provide a clear picture of the state-of-the-art regarding research on Sb2Se3-based solar cells and its prospects, from the successful achievements to the challenges that are still to be overcome. We also report on the key parameters of antimony selenide with a close focus on the different characteristics associated with films grown from different techniques.

2 February 2023 in Coatings
Verified
Journal Article
Open access
PDF file
SPStefano Pasini
Stefano Pasini
DSDonato Spoltore
Donato Spoltore
APAntonella Pariisni
Antonella Pariisni
GFGianluca Foti
Gianluca Foti
SMStefano Marchionna
Stefano Marchionna
ABAlessio Bosio
Alessio Bosio
Sb2Se3 is a typical V2VI3 binary chalcogenide compound characterized by a single crystalline phase and a fixed composition. Sb2Se3 displays a narrow energy gap ranging from 1.1 to 1.3 eV, which are quite optimal values for single-junction solar cells. Earth-abundant and non-toxic components make this material a good candidate for low-cost thin-film solar cells. In substrate configuration, a world record efficiency of 9.2% was recently obtained. Sb2Se3 thin films exhibit an accentuated predisposition to form (Sb4Se6)n ribbons along the [001] direction. This anisotropy heavily influences the charge transport of the photogenerated carriers. In this work, structural characterization of the Sb2Se3 films showed that the crystalline quality and preferential orientation are strongly dependent on the window layer used. To better understand the growth mechanism, Sb2Se3 thin films were deposited by close-spaced sublimation on five different window layers, such as CdS, CdS:F, CdSe, As2S3, and ZnCdS. Sb2Se3-based solar cells, realized in superstrate configuration on these different substrates, evidently demonstrate the influence of the Sb2Se3 preferential orientation on the photovoltaic parameters.

6 May 2025 in Optical Materials
Verified
Journal Article
Open access
AMA. Moumen
A. Moumen
PKPayam Rajabi Kalvani
Payam Rajabi Kalvani
FMF. Mattei
F. Mattei
GFGianluca Foti
Gianluca Foti
APAntonella Pariisni
Antonella Pariisni
RFRoberto Fornari
Roberto Fornari

28 January 2025 in Materials Today Physics
Verified
Journal Article
Open access
FMF. Mattei
F. Mattei
DVD. Vurro
D. Vurro
DSDonato Spoltore
Donato Spoltore
MPMaura Pavesi
Maura Pavesi
PKPayam Rajabi Kalvani
Payam Rajabi Kalvani
RFRoberto Fornari
Roberto Fornari

8 March 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ABAlessio Bosio
Alessio Bosio
SPStefano Pasini
Stefano Pasini
DSDonato Spoltore
Donato Spoltore
GFGianluca Foti
Gianluca Foti
APAntonella Pariisni
Antonella Pariisni
RFRoberto Fornari
Roberto Fornari
Antimony selenide (Sb2Se3) is an Earth-abundant and non-toxic material that stands out as a promising absorber for the fabrication of thin film solar cells. Despite significant advancements in recent years, all the devices reported in the literature exhibit open-circuit voltages well below the theoretical value. Identifying the factors contributing to this low voltage is an essential step for increasing the efficiency beyond the recently attained 10% milestone and moving closer to the theoretical limit. In this paper, we present the results of an in-depth analysis of a Sb2Se3 solar cell in the common superstrate configuration. By making use of current density–voltage characteristic as a function of both temperature and wavelength, capacitance–voltage measurements, and admittance spectroscopy, we ascribe the low open-circuit voltage to the presence of a potential barrier within the absorber material near the junction interface Furthermore, it was observed that the junction behavior in the dark and under illumination changes, which is compatible with the presence of deep electronic levels connected with intrinsic point defects.

6 June 2025 in Coatings
Verified
Journal Article
Open access
PDF file
SSSamaneh Shapouri
Samaneh Shapouri
EIElnaz Irani
Elnaz Irani
PKPayam Rajabi Kalvani
Payam Rajabi Kalvani
SPStefano Pasini
Stefano Pasini
GFGianluca Foti
Gianluca Foti
ABAlessio Bosio
Alessio Bosio
Copper antimony sulfide (CuSbS2) is an affordable and eco-friendly solar absorber with an optimal bandgap and high absorption coefficient, and it stands out as a promising candidate for thin-film solar cells. This study investigates the effects of indium tin oxide (ITO), fluorine-doped tin oxide (FTO), and glass substrates on the microstructural, morphological, and optical properties of CuSbS2 (CAS) layers synthesized via spray pyrolysis. X-ray Diffraction (XRD) and Raman spectroscopy analyses revealed that CAS phases formed on ITO and FTO substrates exhibited a phase composition without additional copper phases. However, the CAS layer on glass contained a copper sulfide (CuS) phase, which can be detrimental for solar cell applications. Furthermore, the influences of the substrate morphology and contact angle on the growth mechanisms of CAS layers was examined, highlighting the relationship between the substrate micromorphology and the resultant film characteristics. Advanced image processing techniques applied to Atomic Force Microscopy (AFM) images of the substrate surfaces facilitated a comprehensive comparison with the surface characteristics of the CAS films grown on those substrates. Field Emission Scanning Electron Microscopy (FESEM) indicated that CAS layers on ITO possessed larger grains than FTO, whereas those on FTO exhibited lower roughness with a more uniform grain distribution. Notably, the optical properties of the CAS layers correlated strongly with their microstructural and morphological characteristics. This work highlights the critical influence of substrate choice on the growth and characteristics of CAS layers through a comparative analysis.