Oleksii Burlachenko

Dr. Oleksii Burlachenko

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
Cezary SenderowskiCezary Senderowski
Cezary Senderowski
NVNataliia Vigilianska
Nataliia Vigilianska
OBOleksii Burlachenko
Oleksii Burlachenko
OGOleksandr Grishchenko
Oleksandr Grishchenko
AMAnatolii Murashov
Anatolii Murashov
SSSergiy Stepanyuk
Sergiy Stepanyuk
The present paper presents a study of the behaviour of Fe3Al intermetallic powders particles based on 86Fe-14Al, 86Fe-14(Fe5Mg), and 60.8Fe-39.2(Ti37.5Al) compositions obtained by mechanochemical synthesis at successive stages of the plasma spraying process: during transfer in the volume of the gas stream and deformation at the moment of impact on the substrate. The effect of the change in current on the size of powder particles during their transfer through the high-temperature stream and the degree of particle deformation upon impact with the substrate was determined. It was found that during transfer through the plasma jet, there was an increase in the average size of sputtering products by two–three times compared to the initial effects of mechanochemical synthesis due to the coagulation of some particles. In this case, an increase in current from 400 to 500 A led to a growth in average particle size by 14–47% due to the partial evaporation of fine particles with an increase in their heating degree. An increase in current also led to a 5–10% growth in particle deformation degree upon impact on the substrate due to the rising temperature and velocity of the plasma jet. Based on the research, the parameters of plasma spraying of mechanically synthesized Fe3Al intermetallic-based powders were determined, at which dense coatings with a thin-lamellar structure were formed.

18 December 2024 in Coatings
Verified
Journal Article
Open access
PDF file
NVNataliia Vigilianska
Nataliia Vigilianska
CICarolina Iantsevitch
Carolina Iantsevitch
TTTania Tsymbalista
Tania Tsymbalista
OBOleksii Burlachenko
Oleksii Burlachenko
OGOleksandr Grishchenko
Oleksandr Grishchenko
Cezary SenderowskiCezary Senderowski
Cezary Senderowski
In this article, the structure formation and phase composition of coatings containing Cr2AlC MAX phase under the conditions of plasma spraying were studied. Mechanical mixtures of commercially available Cr3C2 and Al powders were used as a material for spraying. The amount of aluminium in the mixtures was 9 and 18 wt.%. As a result of studying physicochemical processes occurring during plasma spraying of mechanical mixtures of selected compositions, the formation of coatings containing Cr2AlC MAX phase was established, the synthesis of which occurs both at the stage of the particles flight of initial components in the plasma jet as a result of the collision and coagulation, and at the stage of a coating layer formation as a result of layering particles deformed during the collision–splats. It is shown that for the formation of a denser coating with a higher MAX phase content for spraying, it is rational to use a mixture of chromium carbide powders with 9 wt.% of aluminium. A coating with the composition 91Cr3C2-9Al (wt.%) has high corrosion resistance in operation conditions in a chloride-acetate solution, and by its indicators of corrosion resistance, is not inferior to the Cr3C2-NiCr coating, which is widely used in industry to protect parts from corrosion and wear. The obtained results show the possibility and feasibility of using mechanical mixtures of commercially available powders for the formation of coatings containing Cr2AlC MAX phase instead of expensive synthesized MAX-Cr2AlC powders.

24 February 2023 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VKVolodymyr Mykolayovych Korzhyk
Volodymyr Mykolayovych Korzhyk
OBOleksii Burlachenko
Oleksii Burlachenko
DSDmytro Strohonov
Dmytro Strohonov
NFNataliia Fialko
Nataliia Fialko
MKMaksym Kharlamov
Maksym Kharlamov
SPSviatoslav Peleshenko
Sviatoslav Peleshenko
Existing techniques for applying intermetallide layers are characterized by low productivity, difficulties associated with the maintenance and operation of technological equipment, as well as significant costs for the purchase of materials for spraying. Therefore, modern science shows considerable interest in the development of new, highly effective technologies to form intermetallide coatings on the surface of articles. Such promising techniques include the technology of plasma-arc spraying (PAS) of flux-cored wires. This technique has a number of significant advantages, namely high performance, relative simplicity, as well as the affordability of equipment and materials for coating. This paper reports a study into the structure and properties of coatings obtained by flux-cored wire PAS, in which the steel sheath and aluminum powder filler interact when heated with the exothermic effect of Fe3Al synthesis. The influence of technological parameters of PAS process on the structure and properties of Fe-Al coatings was investigated by means of mathematical planning of the experiment. It was found that in all samples the main phase is an intermetallide of the Fe3Al type. Tests for gas-abrasive wear resistance at room temperature showed that the wear resistance of coatings exceeds the stability of steel S235 by an average of 2 times. As a result of studying the electrochemical properties in a 3-% aqueous solution of NaCl and in a 0.5-% solution of H2SO4, the score of corrosion resistance for these media was determined, which was, respectively, 4 and 5 (coatings belong to the group of "resistant"). In this regard, the practical use of coatings based on the Fe3Al intermetallide is recommended for protection against oxidation, corrosion, and gas-abrasive wear of components and assemblies in the heat power industry (heat exchanger pipes, catalytic converters, steam turbine blades, shut-off valves, etc.)

28 October 2023 in Автоматическая сварка
Verified
Journal Article
Closed access
OGO.P. Gryshchenko
O.P. Gryshchenko
NVN.V. Vihilianska
N.V. Vihilianska
OBOleksii Burlachenko
Oleksii Burlachenko
Cezary SenderowskiCezary Senderowski
Cezary Senderowski
G V.F. Gorban
V.F. Gorban
Automatic Welding, 2023, №10. Journal «AVTOMATICHESKAYA SVARKA» Monthly scientific-technical and production journal. ISSN: 0005-111X, Since 1948. Russian version of «The PATON Welding Journal» Text in Russian, contents and summaries in English. The Journal presents a wide range of scientific-technical and promotion information in the field of technologies, equipment and materials for welding, surfacing, brazing, and deposition of protective coatings.